Our Alberg 30 galley is tiny and we need to maximize every square inch as full-time liveaboards. We have raised counter heights, installed a new sink, ripped out cabinetry, and installed a new water filter as part of a major galley renovation. Materials: Faucet: https://amzn.to/38rsTzG Sink: https://fave.co/2Lz9kfJ Accumulator Tank: https://amzn.to/3q4t8Xf Water Tank: https://fave.co/38u69iz Water Filter: https://amzn.to/38tYP6A Formica: https://fave.co/3otKgFG For all our favorite galley gear: https://abroadreachtravel.com/product-category/galley-gear/ Disclaimer: In the interest of transparency, please be aware that the links above may contain affiliate links and any purchases made through such links may result in a small commission for us at no cost to you. We appreciate you shopping from these links! Check out our Instagram to see our projects happening in real-time https://www.instagram.com/abroadreachtravel/

Many years ago our Alberg 30 was converted to water-jacketed wet exhaust, and we have converted it back to traditional wet exhaust and found a few engine problems in the process! Check out our Instagram to see our projects happening in real-time https://www.instagram.com/abroadreachtravel/

This video shows the interior and exterior of the 1993 Catalina 42 "Wind Graham" in San Diego, CA. Contact sean@scyachts.com for more information.

We cover how we make, store, and use electricity in our off-grid electrical system here on Ecola. From our solar panels, to batteries and chargers, we give a soup to nuts review of our whole system. Our System 200 Watt Solar Panels--https://amzn.to/2U9uoKK 100 Watt Solar Panels--https://amzn.to/2IlW5xy Solar Charge Controllers--https://amzn.to/35bi4Qt Battery to Battery Charger--https://amzn.to/33sezDW Battery Charger--https://amzn.to/3fRqErn Battery Monitor--https://amzn.to/2JqKOfU Batteries--https://battlebornbatteries.com/product/12v-lifepo4-deep-cycle-battery/ Inverter--https://amzn.to/39t9jnq Disclaimer: In the interest of transparency, please be aware that the links above may contain affiliate links and any purchases made through such links may result in a small commission for us at no cost to you. We appreciate you shopping from these links! Check out our Instagram to see our projects happening in real-time https://www.instagram.com/abroadreachtravel/

Putting solar panels on a small boat, especially one as old as our 1965 Alberg 30 presents a lot of challenges. The most glaring is how do you make it so the panels don't detract from the classic lines of the boat. We knew we needed 400-600 watts of solar on Ecola to meet our electricity demands, and planning for this project started over a year ago! Our sliding panel setup is simple and we think it looks great! Materials: 200 Watt Panels--https://amzn.to/2U9uoKK 100 Watt Panels--https://amzn.to/2IlW5xy Solar Charge Controllers--https://amzn.to/35bi4Qt Drawer Slides--https://fave.co/3ld5dTF 820 T-Slot Rails--https://fave.co/3mYPeJc Check out our Instagram to see our projects in real-time! https://www.instagram.com/abroadreachtravel In the interest of transparency, please be aware that the above may contain affiliate links and any purchases made through such links may result in a small commission for us at no cost to you.   We appreciate you shopping from these links!

We were told that it would be basically impossible for a sailboat to transit the New Jersey ICW from Manasquan Inlet to Atlantic City, but a broken autopilot and unfavorable weather had us trying! Our videos are always a few weeks behind, check out our Instagram to see our adventures in real-time! https://www.instagram.com/abroadreachtravel/

This video shows the Mercury Marine 300hp V8 Verado internal components during the Fort Lauderdale International Boat Show inside the Mercury display with Tad showing the design. After the tour you will see the engines start up in San Diego on a brand new Beneteau Gran Turismo 36.

When we sat down to plan the Hudson River leg of our journey, we decided on two must stop destinations. While 2020 put a bit of a wrench in our plans, we still got to stop at Bannerman Castle and New York City! Our videos are always a few weeks behind our real life. Check out our Instagram for real-time updates! https://www.instagram.com/abroadreachtravel

We leave Lake Champlain for the first time in seven years through the Champlain Canal. Our first ever lock was a little bumpy but by the time we made it to the Hudson River, we were feeling much more comfortable! Hope you enjoy this week's episode! Our videos are always a few weeks behind our real life. Check out our Instagram to find out what we are up to in real-time! Https://www.instagram.com/abroadreachtravel/

This video shows the interior and exterior of the 2012 Silverton 40 West Coast Edition in San Diego, CA for sale. Contact Sean@scyachts.com for more information.

We have been dealing with tiller slop for a few years now, and before the head snapped off in a place like New York harbor we decided to replace it. Our old tiller head didn't have a keyway so Andy had to get a little creative with this replacement. Tools Used Dremel Tool: https://amzn.to/2Yj3Md9 Dremel Cutting Tools: https://amzn.to/31zpuLl Materials: Tiller Head: https://www.spartanmarine.com/all-products/1-tiller-strap-and-cap Disclaimer: In the interest of transparency, please be aware that the links above may contain affiliate links and any purchases made through such links may result in a small commission for us at no cost to you. We appreciate you shopping from these links! Check out our Instagram to see our projects happening in real-time https://www.instagram.com/abroadreachtravel/

This is a drone video following the Oceanis Yacht 62 PHASE 8 around San Diego Bay while under sail. For more information about the Oceanis Yacht 62 please contact Sean@scyachts.com.

This video shows the beautiful spaces inside and out of the Beneteau Oceanis Yacht 62 while it sails in San Diego. The exterior footage is shot from a drone. Contact sean@scyachts.com for more information.

Our old cable lifelines were rotten to the core and about one got tug from breaking. We decided to replace them with Dyneema because it would be cheaper and we would be able to see wear as it happened instead of just before/at failure. Tools: Splicing Kit: https://amzn.to/3iksyR0 Ruler: https://amzn.to/3n6OAKt Scissors Permanent Marker Materials: 1/4" Dyneema Rope: https://fave.co/2Sdvynt Videos We Watched: Premium Ropes (The version that requires running the full length of the rope): https://youtu.be/d0B6tYTVHVM Rigging Doctor (The second option that does not require running the full length) https://youtu.be/UpkqJ4GRfSg Check out our Instagram to see our projects happening in real time https://www.instagram.com/abroadreachtravel

Its time for the final assembly :) Nick name: Electric Orange 3000w electric hub motor 48v 40ah battery pack 100v 100Amp Controller. Had this footage since 2017 but just now decided to take the time to edit. I have a lot more footage stay tuned for videos on the complete build.

While our original plan was to use swaged ends for both the tops and bottoms of our standing rigging, we ended up using mechanical fittings at the bottoms and it was so easy! Materials: Wires with Swaged Uppers: https://www.westmarine.com/RiggingServices/Rigging-Shop-Home Mechanical Fittings and Turn Buckles: http://www.riggingonly.com/ Pins and Bolts: https://www.mcmaster.com/ Tools: Cable Cutter (or you could use an angle grinder) Caulk Gun: https://amzn.to/3kIwoVt Caulk: https://amzn.to/3iSAQRj Needle Nose Pliers: https://amzn.to/3kCa7sy Wrenches Stay up to date with our projects in real-time on our Instagram: https://www.instagram.com/abroadreachtravel

I review the Ulefone armor 9 With Flir Camera Bought with mi own money. Im happy with it so far.

Last year, our 35-year-old roller furler quit working, and it was no longer serviceable, so we decided to buy a new roller furler! The Harken MKIV was recommended by every rigger we talked to and was in our price range. We have been sailing with it for 4 months now and it has completely changed how we sail. The ability to reef the jib has been a game-changer! Harken MKIV Unit 1 Roller Furler: https://fave.co/3m0ufGe Harken Unit 1 Long Link Plate: https://fave.co/35lC7w9 Helpful Tools Non-Marring Hammer: https://amzn.to/3ijm31M Screwdriver Set: https://amzn.to/3k2pTwt Be sure to check out our Instagram real time updates on our projects! www.instagram.com/abroadreachtravel

First video renovation on this classic 1989 Hymer B534 in this video we do the top part of the kitchen. build a new controller using a Nextion HMI touch screen and arduino. Also there´s some painting going on. Sub so that you don´t miss the next video. Music: https://www.bensound.com

Its almost time for the final assembly :) in this one i add carbon fiber to the fairings so they lock less blend. Nick name: Electric Orange 3000w electric hub motor 48v 40ah battery pack 100v 100Amp Controller. Had this footage since 2017 but just now decided to take the time to edit. I have a lot more footage stay tuned for videos on the complete build. Music By: Members Only - TrackTribe

This week we chop off the end of our mast to remove damage from a bridge strike and beef up our masthead since it is original and was getting thin. Tools Used: Angle Grinder: https://amzn.to/2X8FWyW Angle Grinder Cutting Wheels: https://amzn.to/2G3vW5e While our videos are always a few weeks behind, check out our Instagram for realtime updates on our projects! https://www.instagram.com/abroadreachtravel

I´m Doing Low Carb OMAD for 30 days, here are the third week results. check back in a week for latest results.

In this video i paint the fairings aka "the plastic thingies" that cover the motorcycle 😎 Nick name: Electric Orange 3000w electric hub motor 48v 40ah battery pack 100v 100Amp Controller. Had this footage since 2017 but just now decided to take the time to edit. I have a lot more footage stay tuned for videos on the complete build. Music By: Members Only - TrackTribe

I´m Doing Low Carb OMAD for 30 days, here are the second week results. check back in a week for latest results.

Separating the front speakers from the lounge speakers using a small inexpensive amplifier. In this video i test the unit to figure out if its safe to install in the motorhome using a lab power supply a flir thermal camera and good sense :) Installation is self explanatory. Finished result was quite pleasing. Only thing left to do is test it on the road.

In this video i Make the battery enclosure for the electric bike conversion. Nick name: Electric Orange 3000w electric hub motor 48v 40ah battery pack 100v 100Amp Controller. Had this footage since 2017 but just now decided to take the time to edit. I have a lot more footage stay tuned for videos on the complete build. Music By: Members Only - TrackTribe

In this video i paint the electric motorcycle frame twice cuz i messed it up bad the fist time. 3000w electric hub motor 48v 40ah battery pack 100v 100Amp Controller. Had this footage since 2017 but just now decided to take the time to edit. I have a lot more footage stay tuned for videos on the complete build. Music By: Members Only - TrackTribe

I´m Doing Low Carb OMAD for 30 days, here are the first week results. check back in a week for latest results.

welding the frame for the electric motorcycle aka Electric Orange. 3000w electric hub motor 48v 40ah battery pack 100v 100Amp Controller. Had this footage since 2017 but just now decided to take the time to edit. I have a lot more footage stay tuned for videos on the complete build. Music By: Members Only - TrackTribe

In this video I´ll take you thru the repair procedure on how to disassemble and fix a classic Hymer 534 motor-home RV Boiler of the Truma brand. If you are living the van life tis might be quite useful, as repairs are usually very expensive.

Building the battery pack for the electric motorcycle aka Electric Orange. 3000w electric hub motor 48v 40ah battery pack 100v 100Amp Controller. Had this footage since 2017 but just now decided to take the time to edit. I have a lot more footage stay tuned for videos on the complete build. Music By: Members Only - TrackTribe

This video shows a brand new Beneteau Oceanis 46.1 sailing from a drone camera as well as a camera on board. This boat was recently purchased and you will see the new owners learning to operate the new boat. Contact sean@scyachts.com for more information or visit https://scyachts.com/new-sailboats/beneteau-oceanis-46-1/.

This video shows a 2019 Beneteau Oceanis 51.1 in San Diego sailing. The video is shot from a drone and also from onboard to show the exterior and interior while sailing. Contact sean@scyachts.com for information about the boat.

This is a tour of the 2019 Beneteau Oceanis 51.1 that is available now in San Diego, CA. The boat has lots of great upgrades, contact sean@scyachts.com for more information.

Last fall Andy couldn't remove our old radar mount, but this time he isn't playing around! Our new mount is a universal mount that works with our new Furuno radar. Check out our Instagram for realtime updates on our projects! https://www.instagram.com/abroadreachtravel

This is a video of the 2019 Beneteau Oceanis Yacht 62 MOONSHADOW sailing filmed with a drone as well as a tour of the interior. The boat is currently for sale, contact Sean@scyachts.com for more info.

This week we install the new chainplates Andy fabricated in Episode 6. We also fix the rotten plywood in our backstay knee using new plywood and epoxy. Tools Used: Dremel Oscillating Tool: https://amzn.to/3elnz1g Dremel Tool: https://amzn.to/2Yj3Md9 Check out our projects as they happen in real-time on our Instagram: https://www.instagram.com/abroadreachtravel

Over the course of several weeks, we scraped and sanded all of our old bottom paint off, including several layers of VC17 which is notoriously hard to remove. We did a new barrier coat and new ablative bottom paint. Andy also rebuilt the rudder shoe and rudder pin on our Alberg 30! We are so excited to have launched Ecola and we have so many more projects coming down the line! Be sure to subscribe to stay up to date!

This video was filmed in San Diego Bay of two Beneteau Oceanis Yacht 62's sailing upwind near the city. The footage was captured by Jeff Spangler via Drone. Both boats are available for sale, contact sean@scyachts.com for more information.

This is a detailed look into the Beneteau Oceanis Yacht 62 "PEARL" that has Beneteau Factory modifications as well as aftermarket additions from vendors in San Diego, CA.

This week Gwen learns how to sew while making new salon cushions! Sailrite 30 minute video: https://www.youtube.com/watch?v=mMm_irFrbHQ&t=733s Sailrite Fabric Calculator: https://www.fabric-calculator.com/MainMenu.aspx Tools: Hot Knife--https://amzn.to/2WONx6O We are undertaking a huge refit project on our Alberg 30! We plan to post weekly videos of our progress as well as project-based videos once each project is complete. If you haven't already, subscribe to keep up with the full project as we post new videos every Sunday! Keep up with our progress in realtime on our Instagram! https://www.instagram.com/abroadreachtravel

Four years ago, Andy rebuilt our wood spreaders and they are already looking rough. We made the decision to switch our wood spreaders to aluminum spreaders. After a quote of over $800 to have new ones made, Andy came up with a plan to DIY our new aluminum set up! Project Materials: Off the Shelf Aluminum Spreader Dwyer Mast 1 1/2" Round-- https://www.downwindmarine.com/Dwyer-Aluminum-Spreaders-Round-p-90890671.html Mounting Plate and Bracket-- https://www.onlinemetals.com Project Tools: Drill--https://amzn.to/3bCtUTF Drill Bit Set--https://amzn.to/3dTRRYc Angle Grinder--https://amzn.to/2X8FWyW We are undertaking a huge refit project on our Alberg 30! We plan to post weekly videos of our progress as well as project-based videos once each project is complete. If you haven't already, subscribe to keep up with the full project as we post new videos every Sunday! Keep up with our progress in realtime on our Instagram! https://www.instagram.com/abroadreachtravel

Our galley is tiny and in order to maximize space in our Alberg 30, our ancient and huge hot water heater had to go! This is just the first step in reconfiguring our galley for maximum storage and efficiency! We are undertaking a huge refit project on our Alberg 30! We plan to post weekly videos of our progress as well as project-based videos once each project is complete. If you haven't already, subscribe to keep up with the full project as we post new videos every Sunday! Keep up with our progress in realtime on our Instagram! https://www.instagram.com/abroadreachtravel

This video is a tour of the sold 1998 Sea Ray 400 Sedan Bridge. Contact Sean@scyachts.com for more information.

This video is a tour of the GT36 sold at South Coast Yachts. Contact sean@scyachts.com for more information about this boat and Beneteau availability.

This video is a tour of the Oceanis 41.1 sold at South Coast Yachts in San Diego. Contact sean@scyachts.com for more information.

This is a video walkthrough tour of the Flyer 32 sold at South Coast Yachts. Contact sean@scyachts.com for more information.

This is a walkthrough tour of Hull #1 of the Swift Trawler 47, contact Sean@scyachts.com for more information.

This walkthrough video shows the Oceanis Yacht 62 "MOONSHADOW". The video starts on the exterior and moves into the interior including all cabins and engine room.

This week Andy measured and ordered our new standing rigging, we talk about how to avoid the mistakes we made during this process, and we unbox all our new shiny parts! Check out our Instagram to see our projects happening in real-time 🛠🔩⛵️ https://www.instagram.com/abroadreachtravel/ For All Our Boat DIY Posts Check Out the Blog: https://abroadreachtravel.com/boat-diy/ Our Alberg 30, Ecola, is a 1965 (early model) that has been in Andy's family for almost 40 years. Keeping her in tip-top shape is almost a full-time job, but it's a labor of love. ❤️ Questions, comments, or want to work with us? Contact us at info@abroadreachtravel.com All Music From Epidemic Sound: https://www.epidemicsound.com/referral/bxowjw/