1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

0

0

0

0

125

Our mission is simple. We want you to achieve results. Your learning is our success, and this course has been designed with this goal solely in mind. You'll begin to learn new concepts and techniques through the videos and resources presented online. Then you'll take our recommended actions combined with your new knowledge and skyrocket your dinghy performance to the next level. Virtual Coaching Sign Up Link: https://discord.gg/virtualcoaching Visit: https://internationalsailingacademy.com/ Laser Sailing Coaching: https://internationalsailingacademy.com/about/ ISA Online: http://learn.internationalsailingacademy.com Laser Sailing Clinics: https://internationalsailingacademy.com/clinic-dates/ #lasersailing #ilca #ilcasailing #sailing #ilcasailors #lasersailboat #laserclinic #ilcaclinic #clinicforlasers #ilcaclinicmexico

0

0

0

313

Catch a glimpse into the evolution of Wild Oats XI as she is prepared to take on all challengers in her 11th tilt at the Rolex Sydney Hobart Yacht Race. View from the Sharp End is the 6th and final teaser, with more glimpses coming up and look out for the full video of her transformation which will be available on-line, on the 19th December. @7NewsSydney @Yachting World @Sailing World magazine @Seahorse Sailing Magazine @Yachting Australia @Sailing Anarchy @Live Sail Die @Sail World @Australian Sailing + Yachting @RolexSydneyHobart @NSW Maritime has @cityofsydney @TPDmedia @Scuttlebutt Sailing News

0

0

0

668