1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

0

0

0

0

87

Ukka, un bavaria 36 cruiser del 2011, con il nuovo armatore, lascia l'ormeggio del Marina di Procida per una lunga navigazione che lo porterà nel porto di Rimini...Speriamo di rivederlo presto alla base nautica di Progettoceano. Ci mancherà!

0

0

0

27

#shorts A bit of raw sailing footage from a passage from South West Rocks to Coffs Harbour (Australia) aboard our Peter Snell Easy 37' "Popao" Let us know in the comments below if you want to see more of these bonus #Shorts For bonus content and giveaways please consider supporting us at Patreon: https://www.patreon.com/uap Buy us a beer! paypal.me/sailingpopao ***OUR GEAR*** Quick Dry Will & Wind Towels https://willandwind.com.au/?ref=svpopao 10% Coupon: 'JESSIE10' Goosehill SUP Board: https://goosehillsport.com/?ref=atc3qwtglr2 10% Coupon: 'JESS10' MOBVOI headphones: https://bit.ly/38fsuie 30% Coupon: 'JessieCripps' Big Camera: https://amzn.to/2UF697i Rode Video Mic: https://amzn.to/2xyMSfy Gopros: https://amzn.to/33SItQX Underwater Video Orca Torch: https://amzn.to/33Xh4NJ Go to Riffe Speargun: https://amzn.to/2JjwaUh Riffe Wetsuit: https://amzn.to/2Us1VRD Jess Dive Mask: https://amzn.to/3bxsoms Best Snorkel in the World: https://amzn.to/3ardrlt Dive Fins: https://amzn.to/3buePUG **SIGN UP** to our website so you never miss a thing: http://www.underwaterallyproductions.com Follow us on Facebook! https://www.facebook.com/underwaterallyadventures https://www.facebook.com/jessie.cripps/ Instagram: https://www.instagram.com/jessie_cripps_sv_popao/ https://www.instagram.com/michaeltakach/

0

0

0

4,433

Nashwa mau makan dulu yakk

0

0

0

25

0

0

0

0

116