Four months ago, we left Maine on our hand built wooden sailboat. Join us in Southwest Florida, as we adventure our way through Cabbage Key and Cayo Costa. We set out on paddleboards to find the elusive "Tunnel of Love," a natural mangrove tunnel that leads into a lagoon on the back side of Cayo Costa. We found it...along with sugar-white sand, a trillion seashells, and the kind of tropical, turquoise water you dream about. View the full episode here - https://youtu.be/BerVXBbMJAs

0

0

0

5,503

Sudan. Shark Dive Expedition Sudan Shark Dive Expedition. There are less than 2 months to start the season of Sudan aboard our brand new Red Sea Blue Force 3. Now is possible to explore the most remote reefs of the Sudanese Red Sea aboard a Premium category diving boat. It will be little more than 3 months of expedition, check availability and book your place! www.blueforcefleet.com We ❤️ the Red Sea!!

0

0

0

385

Congratulations to Elena Kalinina (Russia) for being the only female competitor that made it into the Gold fleet. For more info Facebook: www.facebook.com/hydrofoilprotour www.hydrofoilprotour.info

0

0

0

356

Epic Navigator Σε μία ορεινή εξόρμηση στον Ερύμανθο με τον αδερφό μου εντοπίσαμε ένα παράξενο και φανταχτερό πλασματάκι στο δρόμο. Επρόκειτο για μία Σαλαμάνδρα της φωτιάς ή ευρωπαϊκή Σαλαμάνδρα η οποία είναι ελαφρώς τοξική. Πρόκειται για σπάνιο είδος οπότε εάν τη συναντήσετε βοηθήστε τη να περάσει το δρόμο αλλά πλύνετε και τα χέρια σας μετά...

0

0

0

1,277

The idea behind it is that it hangs onto thin veneers that may otherwise flutter against the tablesaw blade as it reaches the end of the cut. There are other methods for cutting thin veneers which you can explore on YouTube. I find this helpful because it hangs onto the finished veneer as I tend to the billet it just came off. It is also helpful in that it is a one-fence-setting system, unlike cutting veneers off the outboard face of the blade. Of course a fresh push stick is a good idea as is a zero clearance throat plate in your saw. For most standard table saws, that is a simple project in itself. I have a pattern that allows me to make new ones easily. Subject for another video. The extended backboard allows me to fasten this jig to my Jim Tolpin style fence extension. Detail of that can be found in Jim Tolpin’s Tablesaw Magic book. A worthwhile read in its own right. You could eliminate the backboard and recess the end caps allowing f-body clamps to reach in and hold it to any tablesaw fence. I’ll leave other solutions to your own innovation. I use this jig with a Fein shop vac which has a volume control. I was surprised how low I had to turn it down to prevent the stock from locking itself firmly onto the fence, preventing me from feeding it through the blade. You may have to increase the number of saw kerfs through the front of the fence until you find the sweet spot for your vacuum. I would do it one kerf at a time. Note that the kerfs pass all the way through the fence face such that they are exposed on the ends. That is to allow the air to pass behind the stock. I hope this is useful to some of you. Happy wood butchering folks.My website: https://www.nomadboatbuilding.com Instagram: https://www.instagram.com/nomadboatbuilding/ It's not about the money but living isn't free... Products featured in this video: Buy some merch: https://www.nomadboatbuilding.com/shop/ Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding

0

0

0

1,145

0

0

0

0

835