Les UV ayant eu raison de notre diabolo de stick de barre, il a bien fallu en bricoler un nouveau, voici une version bêta non retenue !

0

0

0

526

1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

The 2020 LEGO Luke Skywalker’s Landspeeder is small, but mighty! This is a fantastic set for any lover of Star Wars A New Hope. It is also a great addition to the Master Builder Series Mos Eisley Cantina! Let me know what you think in the comments and don't forget to subscribe to the channel: http://www.youtube.com/channel/UClLxNDGqAWNOTEr35RLyeYw?sub_confirmation=1

0

0

0

45

0

0

0

0

1,058

#Renault #Captur #ETech #fullhybrid 145 hp is now available in dealerships. compact yet spacious inside: 22 cm of leg room in the back, 16 cm sliding bench seat, boot volume of up to 616 L and up to 1,596 L with the bench seat folded down, a total of 24.7 L of storage space, including a glove box with a capacity of 7 L. ➡️ https://bit.ly/4cxUzkL

0

0

0

155,121

EN INCOMPARABLE BECAUSE UNIQUE The BALI CATSMART is a culmination of the latest developments from BALI Catamarans! At 38 feet in length, the CATSMART is the smallest model in the BALI range. A revolution that disrupts the rules and sets new standards in technology, design and comfort for pleasure boating. Discover more on our website: https://www.bali-catamarans.com/en/catamarans/bali-catsmart/ FR INCOMPARABLE PARCE QU’UNIQUE Le BALI CATSMART est un concentré des dernières évolutions de BALI Catamarans ! Avec ses 38 pieds de longueur, il est le plus petit modèle de la gamme. Une révolution qui vient bousculer les règles et établit de nouvelles références en matière de technologie, de design et de confort pour la navigation de plaisance. Découvrez plus sur notre site internet : https://www.bali-catamarans.com/catamarans/bali-catsmart/ ❣️Design your escape

0

0

0

2,219