Navegaremos em mar calmo, águas claras e baixa profundidade. Os coqueirais fazem de Carneiros um belo exemplar de praia nordestina. Em Carneiros fazemos uma parada para banho de mar nos bancos de areia (se maré baixa), outra parada no banho de argila que é um momento divertido e inesquecível, além de uma parada em frente à Capela de São Benedito para tirar fotos da famosa igrejinha da praia. A bordo do nosso catamaran, um guia irá contar curiosidades e histórias do local. Local de embarque - Praia dos Carneiros em frente ao Restaurante Bora-Bora Duração - 2h aproximadamente CASO QUEIRA DESFRUTAR DO RESTAURANTE BORA-BORA COMO PONTO DE APOIO, HÁ COBRANÇA TAXA DE DAY USE NO VALOR DE R$ 30,00 POR PESSOA, CRIANÇAS ATÉ 11 ANOS CORTESIA. (NÃO INCLUSO NO VALOR DO NOSSO PASSEIO). Para acesso ao Bora Bora aconselhamos chegar às 09h pois é bastante concorrido e as vagas esgotam rápido Existe servidão de acesso à Praia dos Carneiros, ao lado do Bora Bora. Também existe estacionamento pago para veículos na pista, próximo ao acesso à servidão. Tempo de caminhada do estacionamento até a Praia - 10 à 15 minutos / 850 metros aproximadamente. COMO ENCONTRAR NOSSA TRIPULAÇÃO PARA CHECK IN E EMBARQUE: Caso opte por acessar à praia pelo Restaurante Bora Bora, um membro da nossa equipe estará recebendo os passageiro ao lado da sorveteria. Caso opte por ir direto para à praia, pode apresentar-se à nossa tripulação que estará a bordo do Catamaran da Catamaran Tours (devidamente adesivado) com bandeira na cor amarela.

0

0

0

1,477

The idea behind it is that it hangs onto thin veneers that may otherwise flutter against the tablesaw blade as it reaches the end of the cut. There are other methods for cutting thin veneers which you can explore on YouTube. I find this helpful because it hangs onto the finished veneer as I tend to the billet it just came off. It is also helpful in that it is a one-fence-setting system, unlike cutting veneers off the outboard face of the blade. Of course a fresh push stick is a good idea as is a zero clearance throat plate in your saw. For most standard table saws, that is a simple project in itself. I have a pattern that allows me to make new ones easily. Subject for another video. The extended backboard allows me to fasten this jig to my Jim Tolpin style fence extension. Detail of that can be found in Jim Tolpin’s Tablesaw Magic book. A worthwhile read in its own right. You could eliminate the backboard and recess the end caps allowing f-body clamps to reach in and hold it to any tablesaw fence. I’ll leave other solutions to your own innovation. I use this jig with a Fein shop vac which has a volume control. I was surprised how low I had to turn it down to prevent the stock from locking itself firmly onto the fence, preventing me from feeding it through the blade. You may have to increase the number of saw kerfs through the front of the fence until you find the sweet spot for your vacuum. I would do it one kerf at a time. Note that the kerfs pass all the way through the fence face such that they are exposed on the ends. That is to allow the air to pass behind the stock. I hope this is useful to some of you. Happy wood butchering folks.My website: https://www.nomadboatbuilding.com Instagram: https://www.instagram.com/nomadboatbuilding/ It's not about the money but living isn't free... Products featured in this video: Buy some merch: https://www.nomadboatbuilding.com/shop/ Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding

0

0

0

1,145

SV Rua Hatu is being returned to the water in Deltaville, VA on Friday, March, 21, 2025.

0

0

0

120

https://www.scanboat.com/en/boat-market/boats/sailingboat-archambault-surprise-17536972 Sailingboat - Både sælges, Archambault Surprise, 1979 EUR 22.000 Scanboat

0

0

0

318

0

0

0

0

1,777