🌊 Join Our Sailing Family Adventure! We’re the Fothergills – a family of six living full-time aboard our catamaran, Happy Days. From tropical islands to remote anchorages, we’re documenting our journey around the world to inspire and encourage others to pursue their own adventure. 🧭 Want to Support the Journey? Join us on Patreon for early video access, uncut updates, behind-the-scenes moments, and exclusive Zoom meetups with the crew: 👉 https://www.patreon.com/sailingwithsix 🛍️ Grab Some Sailing with Six Merch Check out our official store for tees, stickers, and gear that supports our voyage: 👉 https://sailingwithsix.store/ 📸 Follow Our Daily Adventures Instagram: https://www.instagram.com/sailingwithsix Facebook: https://www.facebook.com/sailingwithsix Website & Blog: https://www.sailingwithsix.com 📬 Get Onboard Our Email List Be the first to hear about new videos, digital products, and sailing resources: 👉 https://www.sailingwithsix.com ⚓ New to the Channel? We share what life is really like living aboard with kids — homeschooling, provisioning, sailing mishaps, and the magic in between. 🔔 Don’t forget to subscribe and hit the bell so you never miss an episode. #SailingWithSix #FamilySailing #LiveaboardLife #SailingFamily #TravelWithKids

0

0

0

945

0

0

0

0

515

From tears of joy, to tears of frustration, week 13 of the Vendée Globe was another emotional and dramatic one. And if you thought that the close competition was reserved for the front of the fleet you might want to think again. The 10th edition of the world’s toughest offshore race has delivered the highest level of competition throughout the fleet that the event has ever seen. From the front to the back there have been intense private battles that have lasted for 28,000 miles. And such is the pace this time around that even the tail enders are completing the race quicker than before.

0

0

0

1,369

1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

0

0

0

0

5,595