0

0

0

0

660

O canal oficial da Semana Internacional de Vela de Ilhabela apresenta vídeos promocionais, entrevistas e VTs sobre o principal evento da modalidade na América do Sul. O campeonato chega à sua 46ª edição e será disputado de 13 a 20 de julho, em Ilhabela (SP). São 120 barcos confirmados Não deixe de usar a #SIVILHABELA em seus posts...Curta e compartilhe! Mais informações em https://www.facebook.com/sivilhabela https://www.instagram.com/sivilhabela https://www.twitter.com/sivilhabela Contatos de imprensa: Flávio Perez | Juliana Leite | Katarine Monteiro +55 11 992176474 katarine@onboardsports.net contato@onboardsports.net Vídeos produzidos pela agência On Board Sports em parceria com a Duna Filmes

0

0

0

67

‘Adios’ is a rare diesel powered Formula that incorporates the best of exciting performance and carefree cruising. This beautiful Performance Cruiser delivers a flawless Formula ride along with a wide range of yachting capabilities. The 31 PC has been a popular model for years thanks to a smart layout, quality construction, and solid performance. Some of the features added in 2020 include: Upgraded house and start batteries, new Xantrex inverter/charger, new Garmin electronics new Seaward hot water heater, new organic latex mattress, new plastic carpet covers, new shore power connection, and new exterior carpets which have never been used. Another notable feature is the complete new camper canvas, lenses, framing, and winter cover. There is so much value in this boat; don’t miss your opportunity on this very well maintained diesel family cruiser. Call anytime for an appointment to view.

0

0

0

522

The idea behind it is that it hangs onto thin veneers that may otherwise flutter against the tablesaw blade as it reaches the end of the cut. There are other methods for cutting thin veneers which you can explore on YouTube. I find this helpful because it hangs onto the finished veneer as I tend to the billet it just came off. It is also helpful in that it is a one-fence-setting system, unlike cutting veneers off the outboard face of the blade. Of course a fresh push stick is a good idea as is a zero clearance throat plate in your saw. For most standard table saws, that is a simple project in itself. I have a pattern that allows me to make new ones easily. Subject for another video. The extended backboard allows me to fasten this jig to my Jim Tolpin style fence extension. Detail of that can be found in Jim Tolpin’s Tablesaw Magic book. A worthwhile read in its own right. You could eliminate the backboard and recess the end caps allowing f-body clamps to reach in and hold it to any tablesaw fence. I’ll leave other solutions to your own innovation. I use this jig with a Fein shop vac which has a volume control. I was surprised how low I had to turn it down to prevent the stock from locking itself firmly onto the fence, preventing me from feeding it through the blade. You may have to increase the number of saw kerfs through the front of the fence until you find the sweet spot for your vacuum. I would do it one kerf at a time. Note that the kerfs pass all the way through the fence face such that they are exposed on the ends. That is to allow the air to pass behind the stock. I hope this is useful to some of you. Happy wood butchering folks.My website: https://www.nomadboatbuilding.com Instagram: https://www.instagram.com/nomadboatbuilding/ It's not about the money but living isn't free... Products featured in this video: Buy some merch: https://www.nomadboatbuilding.com/shop/ Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding

0

0

0

1,145

0

0

0

0

3,667