QP show you how she keeps in shape onboard. #beautiful #asian #adorable #gorgeous #fitness #exercise #inshape #bikini #sailboatlife #liveaboard #health #stairs

0

0

0

353

1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

We woke this fella sunning on a Sydney Harbout Channel Marker March 02.19 Good to see that the Harbour's wildlife is booming.

0

0

0

764

Witness the beauty of a sailboat gracefully traversing a tranquil river, set against a backdrop of verdant trees. The J109 Going to Red was locked in a tight tussle with the Melges 24 Supersonic. With the tide pushing the boats into Strangford Lough at over 14 knots over the ground there was only meters between the boats for the first 5 minutes of racing. We will share the last video in this series shortly to give you the result. The team at bottom up boats hope you are enjoying the short bits from the 2025 racing season, and learning a thing or two about boating.

0

0

0

14,384

0

0

0

0

1,093

A beach that requires you go down two Ladders, through a narrow opening and pull yourself up with a rope, this is Tsigrado Beach. The beach itself is small but beautiful with a stunning outlook, one of a kind. It's the most remote beach on Milos and worth the adventure finding it! @SailingKawai #shorts #subscribe #shortvideo #sailing #greece #greekislands #sail #summer #europe #milos #bestgreekisland #fun #isolatedbeach #tsigrado #tsigradobeach #sailingkawai #sail #sailgreece Music 1. I've Found my Feet, Hallman feat ELWIN, www.epidemicsound.com

0

0

0

5,226