Bigger is better right? ⛵️This is how we turned our 43 foot monohull into a 46 footer! On a sailboat you always want more space no matter how big…for us this was one of the most important upgrades and james totally nailed it! Check out the full video in our YouTube channel sailing Zephyr #shorts #sailinglife #sailboatrefit #boatworkstoday #boatwork #sailing #boatlife

0

0

0

46,410

BELLE is a stunning soft-top Picnic Boat Classic meticulously updated with modern systems while preserving her timeless elegance. Setting her apart for most any other Classic, she features a (2021) Yanmar 440 fully electronic common-rail diesel, (2018) IQAN Gen-3 Hinckley JetStick, (2017) Garmin electronics & Fusion stereo system, and (2018) Flag Blue awlgrip hull paint. Always maintained to the highest Hinckley standards, BELLE is currently enrolled in our winter YachtCare package, with commissioning, detailing, exterior & interior varnish, and all seasonal maintenance prepaid for a seamless Spring delivery. With this exceptional level of care, BELLE conveys with Hinckley’s Certified Pre-Owned warranty. Listing link: https://hinckleybrokerage.com/yachts-for-sale/hinckley-picnic-boat-1998-4381870/

0

0

0

2,206

0

0

0

0

2,479

1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

👟 Las zapatillas que no sabías que necesitabas para navegar. Las SB2 de Rooster® están pensadas para quienes buscan rendimiento, comodidad y libertad en cada paso. ✔️ Máximo agarre, incluso en cubierta mojada ✔️ Comodidad sin peso extra ✔️ Secado rápido y transpirables 🌊 Perfectas para moverte sin límites. 🟡 Ya disponibles en Go Sailing Shop 👉 Haz clic y equípate para tu próxima aventura. https://gosailingshop.com/es/products/rooster-sb2-deck-trainer #GoSailingShop #ZapatillasNáuticas #RoosterSB2 #CalzadoDeVela #RopaNáutica #SailingGear #VelaLigera #RoosterSailing #VelaEspaña #SailingShoes

0

0

0

382

0

0

0

0

207