Fight ALS

0

0

0

1,591

Become a patron, https://www.patreon.com/elcanoworldchallenge If you want more information on the Odisea 48, 55 or 62 then send an email to peter@elcanoworldchallenge.org The Odisea 48 from Odisea Catamarans has just started to get built in Vietnam. The design is complete, the paperwork has been done and now the factory has had 4 days to start the job and they are welding like madmen. Finally the wait is over, the Elcano World Challenge will begin in 2024 people. If you would like to help the project along then become a patron and get access to exclusive content. https://patreon.com/elcanoworldchallenge Give it a thumbs up if you liked this episode! Get your Sailing Into Freedom Crew T-shirt: https://teespring.com/stores/sailing-into-freedom If you would like to support with single donations click here - https://www.paypal.me/Plukky Check out some gear we have on the boat: Inverter https://www.amazon.com/Xantrex-PROWatt-Inverter-Model-806-1220/dp/B002LGEMOQ/ref=sr_1_5_mod_primary_new?dchild=1&keywords=marine+inverter&qid=1616102481&sbo=RZvfv%2F%2FHxDF%2BO5021pAnSA%3D%3D&sr=8-5 handheld radio https://www.amazon.com/Standard-Horizon-HX210-6W-Compact/dp/B07KN6LKVG/ref=sr_1_6?dchild=1&keywords=marine+radio&qid=1616102542&sr=8-6 (As an Amazon Associate I earn from qualifying purchases and I greatly appreciate your support!) Also follow us on - Instagram: https://www.instagram.com/sailingintofreedom Facebook: https://www.facebook.com/sailingintofreedom Our website: https://www.sailingintofreedom.comGive it a thumbs up if you liked this episode! Get your Sailing Into Freedom Crew T-shirt: https://teespring.com/stores/sailing-into-freedom If you would like to support with single donations click here - https://www.paypal.me/Plukky

0

0

0

4,063

MERCIE A TOI (((grand chef marinier ))) pour les bonne piece RIRE

0

0

0

28

0

0

0

0

617

0

0

0

0

8,535

Check out the link below for full instructions on how to tie the Highwayman's Hitch. https://youtu.be/USjyE1nTV9Q The Highwayman’s hitch is a quick-release draw hitch used for temporarily securing a load that will need to be released easily and cleanly. The hitch can be untied with a tug of the working end, even when under tension. The highwayman's hitch can be tied in the middle of a rope, and so the working end does not need to be passed around the anchor when tying or releasing. The knot is three bights that each successively lock the previous one: - The first one, in the middle of the rope, wraps around the pole, - The second one (called the toggle bight) is a bight of the standing part locking the first one so the pole is held tight, and - The third one (called the slip-tuck) is a bight of the working part (slack end) locking the second bight. The locking actions are achieved by reaching through each bight to pull the next one through. The knot has to be finished by pulling the standing part tight to ensure that it holds. Until the knot is tightened and properly dressed, the highwayman's hitch has little holding power. The highwayman's hitch is susceptible to capsizing when the pole is substantially larger than the rope diameter. The failure occurs because the second bight sees the force of the standing part, but is held in place by the working part, which has no tension. When capsizing, tension on the standing part pulls the second bight through the first bight. This drags the slip-tuck through, and will release the hitch if the third bight isn't long enough. The team at bottom up boats hope you enjoyed our latest video demonstration where we teach you how to tie the highwayman's hitch.

0

0

0

71,540