0

0

0

0

459

EVERY SAILOR needs a BLACK POWDER winch mount CANNON! (Even if you don't "need" one ... there is no denying that they are BAD ASS! Well thanks to HARBORBURN Cannon Co. we were ablet to pick up our customized cannon at the Annapolis Boat Show! Here comes the BOOM! A signal cannon, also known as a salute cannon, is a small cannon, typically less than two feet in length, used for signaling and saluting rather than for military combat. These cannons were historically used on ships and on land to announce arrivals, warn of danger, or signal distress. They are also commonly used for celebratory events, such as starting sailboat races or marking significant milestones. HARBORBURN makes the only legit, useable, black-powder, muzzle-loading, fuse-lighting, loud-blasting signal cannon on the market. Hand-stamped and customized for your boat name, the ‘Herrington Mk. 1’ cannons are useable artwork and will last a lifetime. HARBORBURN started as a passion project between four sailors who wanted a real, black-powder signal cannon for their own boats, but nothing was available…so we made one! And now it’s available to boats and cannon-enthusiasts alike. You may recognize Andy from the YouTube Sailing Channel 59 North. 59 North is a sailing company founded by Andy Schell and Mia Karlsson, specializing in offshore sailing adventures and education. They offer ocean passages on their two yachts, ISBJORN and FALKEN, and also have a membership site called The Quarterdeck. Andy Schell is also the host of the podcast "On The Wind". Instagram: https://www.instagram.com/mtkaloslife/ Instagram: https://instagram.com/harborburn instagram: https://instagram.com/cruisdersacademy email Haborburn: harborburncannons@gmail.com Subscribe: https://bit.ly/svkalos Watch more svkalos videos: Hawaii Playlist: https://www.youtube.com/playlist?list=PLpUkZy_iNw_reTsW8VkEzoO2VVbGGKTKz Shorts Playlist: https://www.youtube.com/playlist?list=PLpUkZy_iNw_rpJZd2Gxjte80nYosvr4U3 Travel Playlist: https://www.youtube.com/playlist?list=PLpUkZy_iNw_qd0uWonumq9_zteOBZ0bwI Scuba Playlist: https://www.youtube.com/playlist?list=PLpUkZy_iNw_ox6zFG6ZmGf-uGn3n1ysJl Sailing Playlist: https://www.youtube.com/playlist?list=PLpUkZy_iNw_qS7hFrob2ff-OejT9gKSKx Racing BAJA: https://www.youtube.com/playlist?list=PLpUkZy_iNw_qM3wjTfjULM0DtsWz9TEEE ==== #cannons #boatshow #sailboat @59NorthSailing @harborburncannonco.4186 @CruisersAcademy ​

0

0

0

516

1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

0

0

0

0

0

Après la pêche, le ménage ! Du sang de poisson partout sur le pont… faut bien ramasser le dégât 😅 Je nettoie, je câline Windy 🐶, puis direction la douche sauvage à l’arrière du catamaran ! 🌊🚿 [ VISITEZ NOTRE SITE WEB ] https://www.sailingatypic.com [ RÉSERVEZ VOS PROCHAINES VACANCES EN VOILIER ] https://sailingatypic.com/pages/vacances-a-bord [ VISITEZ NOTRE BOUTIQUE DE VÊTEMENTS ATYPIC ] https://sailingatypic.com/collections/all [ AIRALO ] Code promo 3$ de rabais : VERONI7320 https://airalo.pxf.io/c/5786229/2071037/15608 [ SUIVEZ-NOUS ] 🔔 Facebook: http://www.facebook.com/SailingAtypic/ Instagram: https://www.instagram.com/sailing_atypic/?hl=fr YouTube: https://youtube.com/c/SailingAtypic Patreon: https://www.patreon.com/user?u=37205310

0

0

0

1,090

This little mama got “the works” today — spay, rabies vaccine, kitty core vaccine, flea and tick medicine and worming. One visit, a whole new start. 🐾 Thanks to your support, we can keep treating kitties like her - visit www.vettails.com/donate to support our mission! #donate #saveanimals #catlovers #catshorts #catlady #animalrescue

0

0

0

774