Été 2022, Voilier Biloup⛵️ -Sera à la découverte de Notre Beau Territoire. #CoteNord, #Labradors Jusqu'à possibilité du 57em Latitude Nord, #TerreNeuve ,#StPierre#Miquelon , Peur-être #iledelamadelein , Peut-être éraflée #CapBreton , #BaiedesChaleurs . Retour Sur Notre Beau : #FleuveStLaurent .Jusqu'à notre port d'attache #MarinaVillageDeBatiscan. Au Plaisir de vous rencontrer 😁 Voilier Biloup⛵️ Capitaine: Martin Amirale :Nath moussaillon: Niña Notre Tite Fille poilue

0

0

0

683

The idea behind it is that it hangs onto thin veneers that may otherwise flutter against the tablesaw blade as it reaches the end of the cut. There are other methods for cutting thin veneers which you can explore on YouTube. I find this helpful because it hangs onto the finished veneer as I tend to the billet it just came off. It is also helpful in that it is a one-fence-setting system, unlike cutting veneers off the outboard face of the blade. Of course a fresh push stick is a good idea as is a zero clearance throat plate in your saw. For most standard table saws, that is a simple project in itself. I have a pattern that allows me to make new ones easily. Subject for another video. The extended backboard allows me to fasten this jig to my Jim Tolpin style fence extension. Detail of that can be found in Jim Tolpin’s Tablesaw Magic book. A worthwhile read in its own right. You could eliminate the backboard and recess the end caps allowing f-body clamps to reach in and hold it to any tablesaw fence. I’ll leave other solutions to your own innovation. I use this jig with a Fein shop vac which has a volume control. I was surprised how low I had to turn it down to prevent the stock from locking itself firmly onto the fence, preventing me from feeding it through the blade. You may have to increase the number of saw kerfs through the front of the fence until you find the sweet spot for your vacuum. I would do it one kerf at a time. Note that the kerfs pass all the way through the fence face such that they are exposed on the ends. That is to allow the air to pass behind the stock. I hope this is useful to some of you. Happy wood butchering folks.My website: https://www.nomadboatbuilding.com Instagram: https://www.instagram.com/nomadboatbuilding/ It's not about the money but living isn't free... Products featured in this video: Buy some merch: https://www.nomadboatbuilding.com/shop/ Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding

0

0

0

1,145

TRENDING Yacht For Charter - The sensational 50m (164’) motor yacht includes an oversized therapeutic hot tub, superior outdoor deck space, a Michelin-star trained Chef & an exceptional assortment of water toys and activities. Available in the Balearics in August & September. http://bit.ly/2u0lEfx Trending Yacht

0

0

0

782

🔵 Bowline Best Uses Here! https://www.youtube.com/watch?v=Z_aALo4vob4&list=PLDLKwvhW5ipsXaK3EUf2BF74kkloXncWM&pp=gAQBiAQB This is how to tie a Bowline Knot, snap to bowline and tying to a structure. We needed this knot a lot sailing the Bahamas. https://youtube.com/shorts/3gGAWiMhQCc #bowline #sailing #travel

0

0

0

2,304,337

The 3S+ seamlessly blends the finest attributes from our wave, freeride and freestyle boards, offering versatility across three distinct styles of windsurfing. This fusion of contemporary tail design and a more traditional nose outline results in an ideal balance of early planing, speed and agility across a wide spectrum of wind and wave conditions. With the 3S+, you have the versatility to engage in three distinct styles of windsurfing, all encapsulated within a single board. Find out more on https://tabou-boards.com

0

0

0

4,054

0

0

0

0

1,080