First Ever 33 Coupe Available in the USA New 2019 33 Coupe by Scandinavian Delta Powerboats, a versatile cabin cruiser featuring a panoramic sunroof and a 39-knot top speed. Offered fully loaded with numerous upgrades and factory warranties. Conveniently docked in Miami Beach and available now for tours. Loa: 10.95m / 36 ft Length: 9.99m / 33 ft Beam: 3.10m / 10.2 ft Draft: 0.95m / 3.1 ft Bridge Clearance: 3.65 m / 12ft Displacement: 4,300 Kg Power: 2x Volvo Penta D3 220hp Speed: 30 / 39 knots Hours: 75 as of November 2019 Fuel: 550L / 145 Us Gal Fresh Water: 200L / 52 Us Gal Holding Tank: 50L / 13 Us Gal 2019 33 Coupe (SOLD 04/2020): www.Delta33Coupe.com Visit our website: www.DeltaCarbonYachts.com Follow DCY on Instagram: www.Instagram.com/deltacarbonyachts

0

0

0

4,161

Fact #13: The dealers hold their breath every time Ricky Ocean rolls the dice. 🎲😎🌊 Ricky Ocean doesn’t just play games—he controls the table. Follow for more incredible Ricky Ocean facts! #RickyOcean #CasinoLife #CruiseVibes #MarinerOfTheSeas

0

0

0

113

Screwhead teak plugs in 23 seconds!! Having just replaced around 1000 teak screw head plugs…this was the process.. Unscrew every exposed screw: I used a battery drill driver. Drill the hole deeper: I used a 10mm forstner bit as it fitted the existing holes perfectly and did a tidy job. This is subject to having enough teak left to drill deeper. Fortunately Najad were generous with their teak! Try not to drill as far as the fibreglass. Add sealant and replace the screws: I’ve seen videos where they say the screws were just for construction and you can leave them out. That is probably correct but I’m going for better safe than sorry. If the teak was thinner with no room to drill deeper and replace the screws I’d leave them out as a last chance of getting a few more years out of a worn deck. Sealant to stop any water getting into the deck core. I used a hand screwdriver rather than power to replace them as power was tending to rip out the self tapping screws from the fibreglass. Put glue on the plug: I used a polyurethane foaming wood glue. Epoxy would be very strong but mixing all the batches a big pain if you have lots to do. Try to get more glue on the edges than the base of the plug as I had a couple of plugs pushed out as the glue foamed up. Tap in the plug: I used a standard claw hammer as it’s all I had but I daresay a wooden mallet is recommended but the top of the plug is waste material anyway so it matters not. Cut off the excess: I used a Fein multi tool oscillating saw. Be careful with your angle as you don’t want to gouge the surrounding deck. It took me a few goes to master the technique but was pretty quick when I did. I said the top of the plugs were waste but if you found yourself short a lot of them had enough material left to do more holes. Sand flat: I used a random orbit sander with a worn 80 grit pad. I now have fresh patches all over the deck so, once I’ve completed a couple of caulking touch ups, I’ll give the whole deck a very light sanding. You could just leave the newly sanded plug patches to grey down to match the deck if you preferred. And that’s it…repeat many times! Feel free to ask any questions 😊⛵️ #boatlife #liveaboardsailboat #boatmaintenance #najad #boatrepairs

0

0

0

709

Follow World Sailing 🌍⛵️ on: Facebook ➡️ www.facebook.com/worldsailingofficial Instagram ➡️ www.instagram.com/worldsailingofficial Twitter ➡️ www.twitter.com/worldsailing Website ➡️ www.sailing.org Newsletter ➡️ www.sailing.org/newsletter-sign-up

0

0

0

268

0

0

0

0

113