Screwhead teak plugs in 23 seconds!! Having just replaced around 1000 teak screw head plugs…this was the process.. Unscrew every exposed screw: I used a battery drill driver. Drill the hole deeper: I used a 10mm forstner bit as it fitted the existing holes perfectly and did a tidy job. This is subject to having enough teak left to drill deeper. Fortunately Najad were generous with their teak! Try not to drill as far as the fibreglass. Add sealant and replace the screws: I’ve seen videos where they say the screws were just for construction and you can leave them out. That is probably correct but I’m going for better safe than sorry. If the teak was thinner with no room to drill deeper and replace the screws I’d leave them out as a last chance of getting a few more years out of a worn deck. Sealant to stop any water getting into the deck core. I used a hand screwdriver rather than power to replace them as power was tending to rip out the self tapping screws from the fibreglass. Put glue on the plug: I used a polyurethane foaming wood glue. Epoxy would be very strong but mixing all the batches a big pain if you have lots to do. Try to get more glue on the edges than the base of the plug as I had a couple of plugs pushed out as the glue foamed up. Tap in the plug: I used a standard claw hammer as it’s all I had but I daresay a wooden mallet is recommended but the top of the plug is waste material anyway so it matters not. Cut off the excess: I used a Fein multi tool oscillating saw. Be careful with your angle as you don’t want to gouge the surrounding deck. It took me a few goes to master the technique but was pretty quick when I did. I said the top of the plugs were waste but if you found yourself short a lot of them had enough material left to do more holes. Sand flat: I used a random orbit sander with a worn 80 grit pad. I now have fresh patches all over the deck so, once I’ve completed a couple of caulking touch ups, I’ll give the whole deck a very light sanding. You could just leave the newly sanded plug patches to grey down to match the deck if you preferred. And that’s it…repeat many times! Feel free to ask any questions 😊⛵️ #boatlife #liveaboardsailboat #boatmaintenance #najad #boatrepairs

0

0

0

696

0

0

0

0

43

0

0

0

0

18,626

Give it a thumbs up if you liked this episode! Get your Sailing Into Freedom Crew T-shirt: https://teespring.com/stores/sailing-into-freedom Want more? Became our patron and get access to exclusive content. https://www.patreon.com/sailingintofreedom If you would like to support with single donations click here - https://www.paypal.me/Plukky Check out some gear we have on the boat: Inverter https://www.amazon.com/Xantrex-PROWatt-Inverter-Model-806-1220/dp/B002LGEMOQ/ref=sr_1_5_mod_primary_new?dchild=1&keywords=marine+inverter&qid=1616102481&sbo=RZvfv%2F%2FHxDF%2BO5021pAnSA%3D%3D&sr=8-5 handheld radio https://www.amazon.com/Standard-Horizon-HX210-6W-Compact/dp/B07KN6LKVG/ref=sr_1_6?dchild=1&keywords=marine+radio&qid=1616102542&sr=8-6 (As an Amazon Associate I earn from qualifying purchases and I greatly appreciate your support!) Also follow us on - Instagram: https://www.instagram.com/sailingintofreedom Facebook: https://www.facebook.com/sailingintofreedom Our website: https://www.sailingintofreedom.comGive it a thumbs up if you liked this episode! Get your Sailing Into Freedom Crew T-shirt: https://teespring.com/stores/sailing-into-freedom Want more? Became our patron and get access to exclusive content. https://www.patreon.com/sailingintofreedom If you would like to support with single donations click here - https://www.paypal.me/Plukky

0

0

0

550

0

0

0

0

662

The Gunboat 80. Designed to sail faster than the wind in 6+ knots true wind speed. ▫️ This is a no-compromise performance sailing catamaran scrutinized for performance optimisation and built with ultra-lightweight construction technologies. The idea is to sail while everyone else is motoring. ▫️ Gunboat 80.01, Highland Fling, is gracing the race circuit, and Gunboat 80.02 is in build poised to become the ultimate family cruiser. ▫️ This is not the biggest Gunboat ever produced - that accolade goes to Sunshine, a Gunboat 90, but it is getting there. Who knows, we might be seeing even bigger Gunboats in the future? ▫️ @robinchristol6319 @GUNBOATCATAMARANS #love #gunboat #design #superyacht #luxuryyacht #beautiful #luxury ▫️ ▫️ ▫️ LOA 24.65m LWL 23.95m BOA 10.25m DRAFT BOARDS DOWN 5.82m DRAFT BOARDS UP 1.3 - 2.2m MAST CLEARANCE 34.6m MAST LENGTH 30.9m DISPLACEMENT 27 - 28 T DISPLACEMENT MAX LOAD 34 T BRIDGE DECK CLEARANCE 1.15 M FUEL CAPACITY 2 X 700 L WATER CAPACITY 2 X 700 L

0

0

0

7,904