Abone olup lk atanalra kalp atmak

0

0

0

27

0

0

0

0

2,545

I found this on a Florida Beach, it was out of the water in the sand and had been for at least 3hrs. I put it in the water and it swam away. I can't find it in any fish ID guide. I found it at Matanzas Inlet. #helpidentify #identify #mysteryfish #floridafish #hybridfish #hybridanimals

0

0

0

86

1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

Perfection on the water with graceful lines. One of the best 31ft boats on the market. Classy and luxurious, this full Pilothouse model is loaded with amenities. Knot a Bight has 424 hours on twin 300 HP Mercury Verado engines. Look like a pro around the dock with Joystick piloting. Skyhook precision piloting keeps you in one spot without anchoring. Professional and detailed service records available. Mercury Vessel View 7 display screen and dual 12” Raymarine plotters and Radar. This boat has the highly upgraded Torqeedo electric kicker conversion. With a separate throttle and Panther wireless steering. The set-up cost over 25k. 5KW Kohler generator / Tracvision satellite TV / Webasto diesel heat / Fusion media with JL Audio speakers. The cockpit is wide open for fishing and ideal for outdoor dining. With 3 folding benches and a removable table. Plus, a sliding cooktop with drawer storage. 2 Scotty downriggers and trap puller included. To know how incredible this boat is you need to come and experience it yourself! The ride is quiet and soft, with tremendous visibility. This is a boat that says you are in a position to enjoy some of the finer things in life! Please call or email today to schedule a viewing.

0

0

0

938

0

0

0

0

376