0

0

0

0

0

In this remote village in Papua New Guinea, Galip nuts play a vital role! From being a food source to helping mend canoes, locals use every part of the Galip nut tree. Discover how this incredible natural resource serves multiple purposes in everyday life. Places: Sudest Island, Louisiades Archipelago, Papua New Guinea Buy us a coffee ☞ https://buymeacoffee.com/onceuponareef Or Send us a gift ☞ https://throne.com/onceuponareef Follow us: ✔INSTAGRAM: @onceuponareef & @wheres.poppy ✔PATREON ☞ https://www.patreon.com/c/onceuponareef Poppy's YouTube Channel ☞ https://www.youtube.com/wherespoppy 📧 BUSINESS INQUIRIES - onceuponareef@protonmail.com Hey there, we’re Ryan and Poppy, a couple of adventure junkie sailors out to explore the most amazing reefs and islands in the world. We hope by documenting everything this lifestyle encompasses, we will inspire, raise awareness and support on going research to do our part in protecting these natural life systems. Subscribe if you’re on board! #onceuponareef

0

0

0

576

We at Sailing Virgins are creating instructional videos on how to sail that aren’t lame! Join us as we travel through the Caribbean, Croatia, Tahiti, and more and show you the ropes, literally. ---- We are the world's #1 sailing school for millennials-lessons, courses, classes in the Caribbean, Croatia, and Tahiti. ---- In this episode:

0

0

0

4,913

1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

0

0

0

0

2,601