This delightful ORIGINAL cocktail recipe features rum, lemon juice, and Domaine de Canton - a ginger liqueur! 🍹 Ingredients 2 ounces Domaine de Canton 2 ounces rum 3/4 ounce lemon juice, freshly squeezed White of 1 egg (optional) Garnish: Lemon wheel Steps Add Domaine de Canton, rum, lemon juice, and egg white to shaker. Dry-shake for 30 seconds without ice. Add ice and shake again for 30 seconds. Strain into a rocks glass. Cheers! 🥂Drink Responsibly!

0

0

0

504

Anchors aweigh! We’ll be heading to the 𝐒𝐨𝐮𝐭𝐡𝐚𝐦𝐩𝐭𝐨𝐧 show this year with our beautiful 𝘌𝘶𝘳𝘰𝘱𝘦𝘢𝘯 𝘺𝘢𝘤𝘩𝘵 𝘰𝘧 𝘵𝘩𝘦 𝘠𝘦𝘢𝘳 winning 𝐂𝐨𝐧𝐭𝐞𝐬𝐭 𝟓𝟓𝐂𝐒, 17 metres of luxurious joy! ✨ See you there, 19-28 September, you’ll find our expert UK team on Berth M740. #ContestYachts #BuildingDreamsTogether #Contest55CS #EYOTY #Winner #SouthamptonInternationalBoatShow #SIBS

0

0

0

247

0

0

0

0

1

#oceanview #Indonesia #sailingadventure #wonderfulindonesia #liveaboard #sailing #baliindonesia *Indonesia through Indonesian eyes* Thanks for being part of the Seatrek Sailing Adventures community, we can't wait to welcome you on board! Start planning your next great escape! here: 🗺 Schedule | https://www.seatrekbali.com/schedule/ ⛵️ Website | https://www.seatrekbali.com 🙏🏼 Contact Us | info@seatrekbali.com

0

0

0

7,492

Would you change seacock valve 65cm below the water line whilst afloat?! It might not be as scary as you think. This valve body seized up (despite only being 3-4 years old) so I unscrewed it, popped in a wooden bung, bought a new one and screwed it on. The trick is to be prepared. I had all my wooden bungs on hand, covered any electrical equipment and was ready for the worst case scenario. Fortunately, because it was a fairly new fitting, it came undone relatively easily and the job was pretty straight forward 😊💦 And what’s the worst case scenario I was prepared for? The worst case scenario is the thru hull fitting itself breaking off when I attempt to unscrew the valve. What would I do about it? Just tap in one of my many wooden bungs and then arrange to get the boat lifted out! That scenario was quite unlikely but it helps to think through what could happen. What also helped me is that, from previous experimentation on another boat, we have pumps that I know could easily outrun the water coming in through that hole. An uncontrolled inflow through that fitting wouldn’t be good as it would spray seawater everywhere but it’s good to know that the pumps could cope. It’s always counter intuitive and panic inducing to see water flooding in to the boat and I know many people don’t like to pull out their paddle wheel log transducers for that very reason however staying calm and knowing that it would actually take quite a long time to sink through a 3/4” hole means it may not be as bad as you think. Always worth thinking what else could help. Whilst away, shopping for parts, I left Kate armed with cushions as well as wooden bungs as a cushion pushed hard over a hole will slow the flow enough that most bilge pumps would cope. Despite my previous experiments I was even surprised how little water we took on but the point is that, with a little thought and prep, changing a valve or pulling that paddle wheel so it doesn’t foul up needn’t be that stressful or require an expensive lift out. Luckily for me everything went super smoothly this time so no need for backup plans! It does get the heart pumping a bit when you haven’t done it for a while though! 😊💦 #followintrepidbear #sailinglife #sailing #sailor #liveaboard #sailboat #boatlife

0

0

0

678

0

0

0

0

3,121