Navegar a vela por las costas gallegas ya en sí es una gozada. Pero, mientras desarrollas tu pasión, aparecen estas maravillosas de la naturaleza, ya no hay nada que se compare. Ven a tu Masterclass Sailing Txemacapitan. Si quieres ver el vídeo completo, Pincha aquí 👉 https://www.youtube.com/watch?v=bWkccQCWF_M&t=555s Si te ha gustado el vídeo 𝐒𝐮𝐬𝐜𝐫í𝐛𝐞𝐭𝐞 𝐚𝐥 𝐜𝐚𝐧𝐚𝐥 👍 https://www.youtube.com/channel/UCEj3jQf5L9r_LMk_oak6Tqw Así nos ayudas a generar más contenido para ti... los amantes de la navegación y del mar. Y si le das a la campanita 🔔 ya alucino... se nos caerán unas cuantas lagrimillas. También nos puedes seguir en otras plataformas: 𝐈𝐧𝐬𝐭𝐚𝐠𝐫𝐚𝐦 - https://www.instagram.com/sailingtxemacapitan_oficial 𝐓𝐢𝐤 𝐓𝐨𝐤 - https://www.tiktok.com/@sailingtxemacapitan 𝐅𝐚𝐜𝐞𝐛𝐨𝐨𝐤 - https://facebook.com/SailingTxemacapitan

0

0

0

284

Sunsail, a premium yacht charter brand within Travelopia, one of the world’s leading specialist travel groups, combines exceptional value vacations with a cutting-edge fleet of 500 yachts in over 20 of the best cruising destinations worldwide. Driven by freedom and adventure since 1974, Sunsail offers a wide choice of sailing vacations including flotilla, bareboat, skippered, and by-the-cabin options as well as sailing schools and regattas. Sunsail Vacations are carefully crafted for sailors, by sailors, focused on delivering unrivaled performance and service for customers across the world.

0

0

0

5,315

A unique and impressive catamaran!

0

0

0

147

Aloha Marujo! Hoje vamos apresentar este #veleiro de 26 pés! #scorpio26 Surpreendeu por dentro. Está à venda no nosso site. link aqui embaixo e tem uma live bem bacana no nosso Instagram !! Deixa se

0

0

0

225

1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694