The Azimut-Benetti Group celebrated reaching 50 years of age in style at a gala event at the famous Eilenroc Villa with over 500 people, including at least 250 clients participating. Explore more: http://oceanmagazine.com.au/

0

0

0

141

1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

No beds. No showers. No escape. Just 42 days. 4,500 miles. Foiling carbon rockets. 7 elite teams. 1 relentless race around Europe. 🌍⛵ This is The Ocean Race Europe. Starts August 10 in Kiel, Germany. 🇩🇪 🎥 Full video on our channel! Don’t forget to subscribe for more The Ocean Race: https://goo.gl/BzBCwU Check out our full video catalogue: https://goo.gl/nrB9ay Like The Ocean Race on Facebook: https://www.facebook.com/theoceanrace/ Follow on Twitter: https://twitter.com/theoceanrace/ Follow on Instagram: https://www.instagram.com/theoceanrace/ Read More: http://www.theoceanrace.com

0

0

0

1,867

Les équipes de NEEL Trimarans ont testé et approuvé durant l’été 2023 le LibertyKite® 40m². Le constructeur renommé de multicoques a ainsi décidé d’équiper en série l’un de ses tout derniers navires, le LEEN 56 de notre kite révolutionnaire arguant : " Cette innovation réduira considérablement votre consommation de carburant tout en offrant une solution de propulsion alternative". Le LEEN 56, équipé de ce Kite, vous permettra de naviguer plus écologiquement et de gagner en autonomie, tout en préservant la performance qui l'a rendu renommée.

0

0

0

1,288