Welcome aboard to the our video site for sailors. We are being constantly blasted by scammers and pirates, so registration is invite only
contact@sailorsahoy.com with "Invite". No spam, no newsletters. Just a free account
निकर सृजन करना
0
0
0
0
60
LIVESTREAM ALERT: 2018 JJ Giltinan Live Sail Die will conduct two Facebook livestreams each day of the JJ Giltinan Regatta in Sydney with the Auckland Skiff League // Royal Akarana Yacht Club Team. Honda Marine New Zealand C-Tech | Carbon Technology Knight Frank Maersk Line Pre-Race Interviews: Race 1 Sat 3 Mar - SYD 1200 / NZL 1400 Race 2 Sun 4 Mar – SYD 1200 / NZL 1400 Race 3 Tues 6 Mar – SYD 1200 / NZL 1400 Race 4 Wed 7 Mar – SYD 1200 / NZL 1400 Race 5 Thurs 8 Mar – SYD 1200 / NZL 1400 Race 6 Sat 10 Mar – SYD 1145 / NZL 1400 Race 7 Sun 11 Mar – SYD 1145 / NZL 1400 Post-Race Interviews: TBC
0
0
0
50
0
0
0
0
43
0
0
0
0
567
Prenderà il via stasera, 14 maggio 2022, la 67esima edizione della Regata dei Tre Golfi, organizzata dal Circolo Remo e Vela Italia con il patrocinio della FIV e in collaborazione con Yacht Club Italiano, Reale Yacht Club Canottieri Savoia, IMA, ORC, UVAI, AIVE. Maserati Multi70 e le altre circa 150 imbarcazioni iscritte alla regata partiranno in tre flotte scaglionate (alle 18:30 ora locale i multiscafi, alle 19:00 i MAXI, e alle 19:30 tutti gli altri) dalla rada di Santa Lucia sotto le mura di Castel dell’Ovo a Napoli, e leggermente corretti saranno anche i percorsi di gara: circuito di 150 miglia con boa a Li Galli per i multiscafi e monoscafi, e una riduzione per gli yacht d’epoca che gireranno Ventotene anzichè Ponza. Per tutti l’arrivo sarà a Capri. La flotta navigherà tra le isole dei golfi di Napoli, Gaeta e Sorrento nello spettacolo naturale delle isole di Procida, Ischia, Ventotene, Ponza, Capri e in corsa con Maserati Multi70 ci sarà Mana di Riccardo Pavoncelli con skipper Paul Larsen. “Napoli è una città dal carattere unico, dove sono sempre felice di tornare e infatti la Tre Golfi è una regata a cui ho già partecipato in passato, ma per Maserati Multi70 è la prima volta e insieme a tutto l’equipaggio non vediamo l’ora di navigare in queste baie stupende, tra isole così straordinarie”, commenta Giovanni Soldini. Le condizioni meteo intanto preannunciano la prevalenza di venti leggeri: “Con poca aria, sarà una regata lenta e soprattutto tattica, siamo molto contenti di ritrovare Mana e come sempre ce la metteremo tutta”. In questa regata, Giovanni Soldini sarà accompagnato da un equipaggio di 6 velisti: Guido Broggi, Oliver Herrera Perez, Thomas Joffrin, Francesco Pedol, Alberto Riva, Gianluigi Ugolini. #MaseratiMulti70 #TreGolfiSailingWeek Sito web: https://maserati.soldini.it/ Facebook: https://www.facebook.com/giovannisoldini/ Instagram: https://www.instagram.com/giovanni_soldini/ Twitter: https://www.twitter.com/giovannisoldini/
0
0
0
800
1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday
0
0
0
694
