close

Welcome aboard to the our video site for sailors. We are being constantly blasted by scammers and pirates, so registration is  invite only


contact@sailorsahoy.com with "Invite". No spam, no newsletters. Just a free account

Korte broek Opprett

Nouvelle Chaine en Français : @danietmarv https://www.youtube.com/channel/UChdsCViFctCvZiWUxhygMeA

Nomadcitizen

0

0

2,454

⛵ Salty Podcast is LIVE this morning! Billy & Lizzie of @2Brits1Box traded RV roads for salty seas 🌊 … and bought a sailboat! Catch their story in this teaser 🎥 📅 9/6/25 ⏰ 11am CT / 9am PT 👉 Watch here: https://saltyabandon.com/saltypodcast74 #SaltyAbandon #SaltyPodcast #Sailing #SaltyPodcastLive #2Brits1Box

svsaltyabandon

0

0

174

0

Sailingwithsix

0

0

1,892

Mast raising without a crane sounds a daunting prospect but it is actually very straightforward if you prepare properly. Some years ago I wrote an article which you can see here, https://www.sailingcatamarans.com/index.php/articles/11-technical-articles/268-safe-mast-lowering-method so this is really just an update. This video shows my Chat 18, which has a mast from a beach cat, and thus one that could be pushed up by hand, but here I show the system that works on any size mast - the biggest I have raised this way was on a 50ft ketch. The key features are a good tabernacle, a "gin pole" - in this case the boom - and most important, the use of temporary shrouds thus ensuring that the mast cannot fall sideways. These shrouds must have "chainplates" that line up exactly with the tabernacle pivot bolt. When down the mast rests on a, eg, dinghy trailer mast support at the back of the cockpit. If you regularly raise you mast you can fit a trailer roller to the bracket, so it's easy to push the mast to and fro for trailering. The "gooseneck" for the ginpole is a shroud adjuster from my junk box, suitably bent and screwed to the front of the mast. Roller reefing gear has to be kept straight and has a tendency to catch on the cabin roof etc. So I always lash it to the ginpole in about the right position. The "chainplates" for the temporary shrouds are, again, from my junk box and are 25mm OD aluminium tubes that clip into place and are easily removed. They also take guywires from the forward end of the ginpole to stop that falling over. I attached the spi halyard to the ginpole, but you can just rely on the forestay/furling gear. The mast is then raised up using the mainsheet shackled to the forestay chainplate (you may need a longer rope, depending on your boat). 4:1 is easy on small boats, on bigger boats lead it back to a winch. Of course the most load is when the mast is horizontal, you often have to push on the mast when lowering to get it to start moving. So if you can get it off the support you know you can hoist it all the way. So it all seems a lot of ropes and preparation but it's all worth it as the mast cannot fall and you always have total control, even in a cross wind. And you can usually raise the mast singlehanded. If you are only occasionally raising/lowering the mast then the temporary stays can be rope. Make a loop in the end and pass it over the spreaders and round the mast using a boathook or, on bigger boats, a bosun's chair. Easy to pull off again afterwards. Before sailing always check the mast with binoculars or camera to ensure there are no twisted shackles or, especially, T bar terminals (which is why I don't recommend T bars on trailable boats.) Use tape or elastic band to hold the stays in the correct position while hoisting - both will break away as the shrouds tighten.

woodsdesigns

0

0

2,234

Sorry! This promotion is no longer valid. But you can buy the movie here: https://vimeo.com/ondemand/utl Follow this link to get 25% off the full movie length documentary Untie The Lines here https://vimeo.com/r/2eHd/MG9NekQ1ZG. Hurry up, ‘cause there won’t be more about that next week!

Nike Steiger

0

0

14,278

Yanmar Marine are welcomed aboard as the Official Marine Supplier for the 36th America's Cup. The America’s Cup embraces technical innovation and Yanmar’s marine engines have been selected to deliver exceptional on-water operations at all AC36 events around the world leading up to and including Auckland 2021. Subscribe to see all America's Cup content. For more information on the America's Cup visit: https://www.americascup.com Like us on Facebook: https://www.facebook.com/AmericasCup/ Follow us on Instagram: https://www.instagram.com/americascup/ Follow us on Twitter: https://twitter.com/americascup #AC36 #AmericasCup

americascup

0

0

576