Vi ligger på svaj i Gluppö och ovädret drar förbi....

0

0

0

616

Just a short sunrise drone clip over Limpini Park in bangkok Thailand. Check out the Komodo dragon at the end! We need your help to keep making videos. You can become a patron for as little as $1 per week! http://www.sailingdoodles.com Become a Patron! http://www.patreon.com/sailingdoodles Donate Via Paypal to help us get a new drone: http://www.paypal.me/sailingdoodles Would you like to join us on the boat? Visit our GoFundMe Page to find out how you can! http://www.gofundme.com/sailingdoodles These are things like camera equipment and a new drone that we really could use to make better videos for you to enjoy: http://a.co/aywvyeM Bobby@sailingdoodles.com Facebook http://www.facebook.com/sailingdoodles Instagram http://www.instagram.com/sailingdoodles Cameras Used: (if you buy from these links we get a small percentage, does not cost you more) Drone - Yuneec Typhoon Q500 4K http://amzn.to/2noNflM Sony A6000 http://amzn.to/2ne2Kgz GoPro Hero 4 http://amzn.to/2ne4GWs Fuji waterproof http://amzn.to/2mHOlVS Music: The Fade - Daniel Gunnarsson #sailing #sailingdoodles #sail

0

0

0

13,047

10 Tage segeln und trekken Segeltörn und Erlebnisreise am Schnittpunkt Afrika - Europa Segeln über die Straße von Gibraltar von Europa nach Afrika 5 Tage Trekking entlang eines unberührten Flusstales im Rif-Gebirge weitab der Zivilisation durch touristisch unerschlossenes Gebiet einsame Lagerplätze am Flusslauf unter freiem Himmel Besuch der marokkanischen Königsstadt Tetouan und Gibraltar https://sailorama-segelreisen.de/de/

0

0

0

47

0

0

0

0

1,319

The idea behind it is that it hangs onto thin veneers that may otherwise flutter against the tablesaw blade as it reaches the end of the cut. There are other methods for cutting thin veneers which you can explore on YouTube. I find this helpful because it hangs onto the finished veneer as I tend to the billet it just came off. It is also helpful in that it is a one-fence-setting system, unlike cutting veneers off the outboard face of the blade. Of course a fresh push stick is a good idea as is a zero clearance throat plate in your saw. For most standard table saws, that is a simple project in itself. I have a pattern that allows me to make new ones easily. Subject for another video. The extended backboard allows me to fasten this jig to my Jim Tolpin style fence extension. Detail of that can be found in Jim Tolpin’s Tablesaw Magic book. A worthwhile read in its own right. You could eliminate the backboard and recess the end caps allowing f-body clamps to reach in and hold it to any tablesaw fence. I’ll leave other solutions to your own innovation. I use this jig with a Fein shop vac which has a volume control. I was surprised how low I had to turn it down to prevent the stock from locking itself firmly onto the fence, preventing me from feeding it through the blade. You may have to increase the number of saw kerfs through the front of the fence until you find the sweet spot for your vacuum. I would do it one kerf at a time. Note that the kerfs pass all the way through the fence face such that they are exposed on the ends. That is to allow the air to pass behind the stock. I hope this is useful to some of you. Happy wood butchering folks.My website: https://www.nomadboatbuilding.com Instagram: https://www.instagram.com/nomadboatbuilding/ It's not about the money but living isn't free... Products featured in this video: Buy some merch: https://www.nomadboatbuilding.com/shop/ Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding

0

0

0

1,145