0

0

0

0

1,794

UCUZA TEKNE ALAYIM DERKEN CANINIZDAN OLMAYIN.#yelkenli_tekne #sailing #yelkenli #shorts #karavan #bitcoin #bim

0

0

0

698

Christos Loizou free style Αν θέλετε να βοηθήσετε το κανάλι μου ✿ Donate: https://streamlabs.com/cyprussailingtv ✿ Donate: https://www.paypal.com/paypalme/CSTVdonates ✿ https://www.youtube.com/channel/UCCMGjQyz6ae96txsX07aoZw/join ★★Social Media★★ ✔Facebook https://www.facebook.com/cyprussailingtv/ ✔Instagram https://www.instagram.com/cyprus_sailing_tv ✔twitter https://twitter.com/cyprussailing ✔Discord https://discord.gg/KnGGjcfyS9 Πηγές / Link: Σας ευχαριστούμε πολύ που είδατε αυτό το βίντεο! Αν σας άρεσε, παρακαλούμε κάντε ένα like , καθώς και εγγραφή στο κανάλι μας, αν δεν το έχετε κάνει ήδη. Είναι δωρεάν! Μπορείτε να εγγραφείτε κάνοντας κλικ εδώ: http://www.youtube.com/c/CyprusSailingTV?sub_confirmation=1 *Τα βίντεο που χρησιμοποιούνται σε αυτή τη συλλογή πληρούν τις προϋποθέσεις για δίκαιη χρήση* Argyris Gregoriou - Cyprus Sailing Tv owner Offshore Sailing Skipper Instructor/ Εκπαιδευτής Ιστιοπλοΐας Ανοιχτής θαλάσσης Master Of Yacht Offshore 200GT VHF Operator STCW crowd management training in a-v/2-1 STCW Basic Safety Training vi/1 a-vi/1.2 Sailing dinghy Instructor/Εκπαιδευτής Ακαδημιών Ιστιοπλοΐας (world sailing national training program) Sailing dinghy coach/ Προπονητή Ιστιοπλοΐας Τριγώνου (world sailing national training program) National Race Officer Sailing article columnist /autho/Αρθρογράφος

0

0

0

247

Watch as we tackle unexpected challenges installing a washing machine! From precise measurements to creative wall modifications, see how we overcome obstacles and get the job done. This DIY project is full of helpful tips and unexpected twists! #DIY #HomeImprovement #WashingMachineInstallation #Plumbing #HomeRepair #UnexpectedChallenges #ProblemSolving #DIYProjects #HomeReno #LifeHacks

0

0

0

452

The idea behind it is that it hangs onto thin veneers that may otherwise flutter against the tablesaw blade as it reaches the end of the cut. There are other methods for cutting thin veneers which you can explore on YouTube. I find this helpful because it hangs onto the finished veneer as I tend to the billet it just came off. It is also helpful in that it is a one-fence-setting system, unlike cutting veneers off the outboard face of the blade. Of course a fresh push stick is a good idea as is a zero clearance throat plate in your saw. For most standard table saws, that is a simple project in itself. I have a pattern that allows me to make new ones easily. Subject for another video. The extended backboard allows me to fasten this jig to my Jim Tolpin style fence extension. Detail of that can be found in Jim Tolpin’s Tablesaw Magic book. A worthwhile read in its own right. You could eliminate the backboard and recess the end caps allowing f-body clamps to reach in and hold it to any tablesaw fence. I’ll leave other solutions to your own innovation. I use this jig with a Fein shop vac which has a volume control. I was surprised how low I had to turn it down to prevent the stock from locking itself firmly onto the fence, preventing me from feeding it through the blade. You may have to increase the number of saw kerfs through the front of the fence until you find the sweet spot for your vacuum. I would do it one kerf at a time. Note that the kerfs pass all the way through the fence face such that they are exposed on the ends. That is to allow the air to pass behind the stock. I hope this is useful to some of you. Happy wood butchering folks.My website: https://www.nomadboatbuilding.com Instagram: https://www.instagram.com/nomadboatbuilding/ It's not about the money but living isn't free... Products featured in this video: Buy some merch: https://www.nomadboatbuilding.com/shop/ Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding

0

0

0

1,145