Sail&Surf Pollensa - Deine Segelschule auf Mallorca Holt Euch ein wenig Urlaub nach Hause. Für alle die uns vermissen oder kennenlernen möchten. www.sailsurf.de info@sailsurf.de Facebook: http://on.fb.me/SaDMf8

0

0

0

217

Our budget liveaboard Mimic is incredibly popular and receives rave reviews. But everybody asks about the sleeping arrangements....so here is a video of how the upper deck daytime relaxing area becomes the sleeping area for the night.

0

0

0

2,937

🇫🇷 // Après une parenthèse européenne cette été, retour à la préparation d’un double défi inédit à l’automne : la Transat Café L’Or en octobre et la TransMartinique en novembre 👊🏼 Cette année, Conrad et Mathieu Blanchard se lancent un double défi, en intégrant l’univers de l’autre. 🇳🇿🇺🇸// After a European summer break, training is back in full swing for a bold autumn double: the Transat Café L’Or in October and the TransMartinique in November. This year, Conrad and Mathieu Blanchard are taking on a double challenge by stepping into each other’s world 💥 🎥 Georgia Schofield Social medias : Facebook : https://www.facebook.com/conradcolmanoceanracing Instagram : https://www.instagram.com/conradcolman

0

0

0

48

1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

Enjoy part 1 of 2 of this #shorts tour of this 2002 Menorquin 120 To see more and/or want more information? Full long form tour here: https://youtu.be/Gh-RoSiDgPk Location: Stuart, FL #sailboat #yacht #boattour #yachttour #trawler #trawlertour #cruising

0

0

0

151,230

Verkäufer und Käufer treffen sich bei ”Boote zu verkaufen”. Scanboat bietet die Möglichkeit zwischen Segelboote, Motorboote und vieles mehr aus ganz Europa zu Suchen. Wenn Sie Ihr Suchergebnis haben und eingeloggt sind, haben Sie auch die Möglichkeit, einen Suchagenten zu aktivieren. https://scanboat.com/de/bootsmarkt/boote https://www.scanboat.com/en/0

0

0

0

60