Sailing the Exploration 52 through the stunning landscapes of Orkney. The perfect blend of performance and exploration.Is Scotland on your sailing bucket list? Let us know in the comments! 👇Hashtags:#GarciaYachts #E52 #Sailing #Scotland #OrkneyIslands #Yachting #ExploreTheWorld #SailingReels

0

0

0

130

1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

0

0

0

0

1,386

0

0

0

0

1,039

Thanks for watching! Please subscribe and leave a comment ⛵️ To support our work ❤️ https://www.patreon.com/sailingrubyrose Our videos are free for everyone to watch, and always will be. However, we have an amazing community of Patrons who, for the cost of a cup of coffee a month, receive all sorts of benefits and perks. This support allows us to continue bringing our stories to you, so a HUGE thanks to our wonderful Patrons 😊 Click the link above to find out more. SOCIAL MEDIA http://www.instagram.com/sailingrubyrose http://www.facebook.com/sailingrubyrose https://www.tiktok.com/@sailingrubyrose MUSIC Epidemic Sound Artlist Hey there! We're Nick and Terysa and we’ve become completely obsessed with the idea of sailing around the world and sharing our experiences and information through our sailing lifestyle videos with others. We met travelling around India, and quickly agreed that rather than “settling down” and doing what most normal people do, we wanted to travel and have adventures! We moved onto our 38 foot monohull in 2014, sailed across the Atlantic twice, cruised the Caribbean, Bahamas and Europe, before buying a brand new 45 ft catamaran! We hope you enjoy what we do. Please subscribe, like and share.

0

0

0

2,635

0

0

0

0

379