Subscribe !! https://www.youtube.com/c/svdreamchaser?sub_confirmation=1 Support !! http://www.patreon.com/svdreamchaser Lets Connect !! - On all the Socials !! -https://www.instagram.com/grillingpitboss/ -https://www.instagram.com/svdreamchaser/ - http://www.facebook.com/svdreamchaser - http://www.twitter.com/svdreamchaser - http://svdreamchaser.tumbler.com

0

0

0

1,234

The SEVENTY 7 is a superior catamaran that has been customized to your individual vision, increasing your sailing pleasure. Learn more about this, as well as all other amazing Lagoon catamarans, at the Düsseldorf Boat Show from January 18 to 26 next year. 🗣️ Registration for this event is already open on our website, so head over to 👉 masteryachting.com #lagooncatamarans #SEVENTY7 #newlagoon #newcatamaran #MasterYachting #YachtingWorld #MasterYachtingGroup #Catamaran #LagoonSEVENTY7

0

0

0

200

Sailing with Taylor Swift #sailing #boat #shorts

0

0

0

9

0

0

0

0

399

1. Remove the old caulking. We use a special tool from @teakdeckingsystems. 2. If your deck is both screwed and glued, considwe removing the screws. We chose to remove the screws since they only created a possibility for water to enter the construction. 3. Fill out every screw hole with epoxy. During the renovation, we learned it would be a good idea to fill the holes with epoxy as soon as you remove the screws to ensure you seal every single hole. 4. Route between all the teak strips. We routed all the way to the gel coat to have as much wood to work with as possible. We used a fine cutter where the caulking was across the grain. 5. Seam sanding. It helps remove the remaining caulking and gives the teak a fresh bonding surface. 6. Masking the teak strips. We chose to mask the wood to reduce the sanding process later on because we knew the teak wasn’t very thick. 7. Cleaning off with acetone. This helps remove dust and gives the caulking the best conditions to adhere to the wood and cure. 8. Start caulking. We used an air compressor caulking gun. It makes the process easier for large surfaces that need caulking - we used SIS 440 from @teakdeckingsystems. We also used a 3D-printed applicator for the caulk head, which minimizes the amount of caulking used. I could only find it on @hfindustrimarineaps website. 9. “Spoon” caulk further into the seams. We used a flexible putty knife to smoothing the caulking. 10. Pull off the masking. While removing the tape, we used scissors to cut just before the area where it hadn’t been caulked yet. 11. Remove the top of the caulking. We used a sharp stanley knife. We did this to minimize sanding, just as we did with masking. 12. Sanding with grit 80. We used the fine cutter’s sanding head for all the edges and an orbital sander for the larger areas. Side note: Sanding with grit 40. We believe the best way is to sand before routing to even out the wood. Unfortunately, we had many places where the wood was so worn out that it wouldn’t have been possible to follow the old tracks with the router after sanding. #diy #sailing #sailingdiy #teak #teakdeck #sailingdenmark #boatwork #shortoftheday

0

0

0

694

The Magic of Foiling: „Foiling is one of the things you have to experience to really feel it“ (Jimmy Spithill) - These stunning images capture the heart-pounding action and the rugged beauty of nature at its finest. Get ready to feel the rush of the wind and the pulse of the waves as the iFLY sails through the untamed waters of Miami! Breathtaking vistas of iFLY15 gracefully navigating the shimmering waters of Miami. Each ripple in the water tells a tale of adventure, echoing the whispers of sailors who've come before. Join us as we embark on an adventure like no other, where every moment is filled with excitement and the promise of discovery. Tag a friend who yearns for the serenity of the open water, and let's weave our stories together on this voyage of discovery. more to know: https://iFLYsail.com

0

0

0

1,433