Viaje organizado en velero por plazas https://totavela.com/es/actividad/ibiza-y-formentera-en-velero/

0

0

0

76

The idea behind it is that it hangs onto thin veneers that may otherwise flutter against the tablesaw blade as it reaches the end of the cut. There are other methods for cutting thin veneers which you can explore on YouTube. I find this helpful because it hangs onto the finished veneer as I tend to the billet it just came off. It is also helpful in that it is a one-fence-setting system, unlike cutting veneers off the outboard face of the blade. Of course a fresh push stick is a good idea as is a zero clearance throat plate in your saw. For most standard table saws, that is a simple project in itself. I have a pattern that allows me to make new ones easily. Subject for another video. The extended backboard allows me to fasten this jig to my Jim Tolpin style fence extension. Detail of that can be found in Jim Tolpin’s Tablesaw Magic book. A worthwhile read in its own right. You could eliminate the backboard and recess the end caps allowing f-body clamps to reach in and hold it to any tablesaw fence. I’ll leave other solutions to your own innovation. I use this jig with a Fein shop vac which has a volume control. I was surprised how low I had to turn it down to prevent the stock from locking itself firmly onto the fence, preventing me from feeding it through the blade. You may have to increase the number of saw kerfs through the front of the fence until you find the sweet spot for your vacuum. I would do it one kerf at a time. Note that the kerfs pass all the way through the fence face such that they are exposed on the ends. That is to allow the air to pass behind the stock. I hope this is useful to some of you. Happy wood butchering folks.My website: https://www.nomadboatbuilding.com Instagram: https://www.instagram.com/nomadboatbuilding/ It's not about the money but living isn't free... Products featured in this video: Buy some merch: https://www.nomadboatbuilding.com/shop/ Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding

0

0

0

1,145

We spent the day aboard the gorgeous Sunreef 80 Nauti Nickel, and got a lift there with her insane tender RONIN! Thanks to the crew for an awesome day, book Nauti Nickel & RONIN for your own vacation: 📧crewed@horizonyachtcharters.com 🧑‍💻horizonyachtcharters.com/crewed

0

0

0

289

Tras estos días tan tristes 🥲 y sin publicaciones, debido a la catástrofe de Mira, provincia de Valencia,… seguimos compartiendo nuestra historia con todos vosotros, en nuestro trabajo diario en La Sonámbula, ⛵️para dejarla a punto lo antes posible para poder seguir esta AVENTURA hacia el Canal de Panamá! . . . #sail #sailing #barco #barcos #catamaran #sailing_lasonambula #velero #paradise #caribe #caribbean #carib #navegar #navegaravela #navegarporelmundo #sailingaroundtheworld #navegaravela #island #colombia #colombiatravel #colombian #varadero #marinapuertovelero #drymarine #colombianos #colombian #batteries #battery #bateria #batería #baterias

0

0

0

1,180

0

0

0

0

485

This Beautiful 19,60 m long Motor Wood Gulet was built in 1988 by J. Akdenniz in Turkey. It is registered with German Flag. This gulet is lying in Ibiza, and viewings are available through Network Yacht Brokers. The boat is used privately by a family that sails around the Balearics and Spain from May to October. During the year, the boat stays 2-4 weeks in the yard and 11 months in the water. The owner wants to sell it because the boat became too big for them as the children grew up, and they no longer follow their parents. A gulet is a perfect boat for coastal sailing in the Med. The hull was built between 1984 y 1987. Commissioned in1988. In its life, the boat had approximately five owners and only sailed in the Med.

0

0

0

348