Darf ich euch unsere wunderschöne Haehaa vorstellen? ?? Sie ist eine Pahi 42/Captain Cook - ein 1980 entwickeltes Design von James Wharram. Orientiert wurde sich beim Baustil an den polynesischen Doppelkanus. Also was könnte besser zu ihr passen als ein polynesischer Name? ? "Haehaa" heißt übersetzt so viel wie Bescheidenheit/ Demut und so haben wir diesen wunderschönen Namen gern übernommen, auch als stetige Erinnerung daran, wie wir mit diesem Boot reisen und durchs Leben gehen wollen. ?? Haehaa ist 12,80m lang, 6,70m breit und hat einen Tiefgang von 0,80m. Sie ist ein Eigenbau aus Sperrholz und Epoxy und wurde im Jahr 2000 fertiggestellt. Anstelle des traditionellen Gaffel-Riggs besitzt sie ein etwas handlicheres Kutter-Rigg. ? Wir könnten ewig weiter über dieses wunderschöne Boot reden, aber vielleicht erstmal die Frage an euch: Gibt es etwas, was euch noch interessiert? ? Dann lasst gern einen Kommentar da! #shorts #wharramcatamaran #wharramdesigns #pahi42 #katamaran #segelreise #travelcouple #langfahrt #liveaboards #sail#boatlife #blauwassersegeln

0

0

0

3,464

We have a brand new Leopard 44 coming to market. I have the prelim spec sheet below with information on the boat. She'll be filmed next week, and will more than likely sell quickly Check out the link below: https://bit.ly/Leopard44DenaliMist Wiley Sharp 561 613 8985 Wiley@CatamaranCentral.com

0

0

0

2,493

The idea behind it is that it hangs onto thin veneers that may otherwise flutter against the tablesaw blade as it reaches the end of the cut. There are other methods for cutting thin veneers which you can explore on YouTube. I find this helpful because it hangs onto the finished veneer as I tend to the billet it just came off. It is also helpful in that it is a one-fence-setting system, unlike cutting veneers off the outboard face of the blade. Of course a fresh push stick is a good idea as is a zero clearance throat plate in your saw. For most standard table saws, that is a simple project in itself. I have a pattern that allows me to make new ones easily. Subject for another video. The extended backboard allows me to fasten this jig to my Jim Tolpin style fence extension. Detail of that can be found in Jim Tolpin's Tablesaw Magic book. A worthwhile read in its own right. You could eliminate the backboard and recess the end caps allowing f-body clamps to reach in and hold it to any tablesaw fence. I'll leave other solutions to your own innovation. I use this jig with a Fein shop vac which has a volume control. I was surprised how low I had to turn it down to prevent the stock from locking itself firmly onto the fence, preventing me from feeding it through the blade. You may have to increase the number of saw kerfs through the front of the fence until you find the sweet spot for your vacuum. I would do it one kerf at a time. Note that the kerfs pass all the way through the fence face such that they are exposed on the ends. That is to allow the air to pass behind the stock. I hope this is useful to some of you. Happy wood butchering folks.My website: https://www.nomadboatbuilding.com Instagram: https://www.instagram.com/nomadboatbuilding/ It's not about the money but living isn't free... Products featured in this video: Buy some merch: https://www.nomadboatbuilding.com/shop/ Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding

0

0

0

1,133

0

0

0

0

593

0

0

0

0

62

PREPARING YOUR LINES: Singlehanded Docking Stern To with Lazy Lines When docking your aim is to reduce the amount of time it takes to get your control line on . Here in video 5 Nick gives great practical tips to make it easier on both you and the person on the dock. Video 5 in Nicks step by step process getting set up and ready for Singlehanded Docking Stern To with Lazy Lines. =========================== TRANSCRIPT I didn't explain it. Just before we do this instead of having the whole line coiled to throw to the guy on the dock. Depending on the system on the dock. It could be a bollard or a ring. Quite often in the marinas like today it's a ring. So if you throw him the whole line, he's got to then find the end, untangle what you threw him, feed it through the ring and get it back to you. What you want to do when you're docking on your own or at any time is to reduce the amount of time it takes to get your control line on. So by throwing him just a manageable amount of line there he can get the end and feed it through and the slack will run out nice and easy =========================== Filmed and Edited by Mahina Hathaway and Nick Hathaway, 45 Degrees Sailing Looking to sail in Croatia? Here are four ways we can help make it happen! ?? ?? Premium Tours ?? ?? https://rb.gy/wrvmtg ?? ?? Flotilla Sailing Weeks ?? ?? https://rb.gy/xozady ?? ?? Bareboat Charters ?? ?? https://rb.gy/yg7l2v ?? ?? Buy a Yacht ?? ?? https://rb.gy/afxrbv =========================== Connect with Us on Social Media: =========================== ?? https://www.linkedin.com/company/45-degrees-sailing/ ?? https://www.facebook.com/45degreessailing ?? https://www.instagram.com/45degreessailing/

0

0

0

1,069