0

0

0

0

1,441

Thank you for watching 🦜 Indonesia through Indonesian eyes 🇮🇩 At SeaTrek Sailing Adventures we have made it our trademark to offer unique and authentic, small-ship cruising experiences that embrace the traditional wooden pinisi boat culture of Indonesia and the fascinating cultural and natural beauty that the remote part of this mighty archipelago in which we cruise has to offer. Check your cabins here: 🗺 Schedule | https://www.seatrekbali.com/schedule/ ⛵️ Website | https://www.seatrekbali.com 🙏🏼 Contact Us | info@seatrekbali.com FOLLOW / SUBSCRIBE: Facebook | https://www.facebook.com/SeaTrekSailingAdventures/ Instagram | https://www.instagram.com/seatreksailingadventures/ Twitter | https://twitter.com/Seatrekbali . #sailingadventures #sailingindonesia #jewelofrajaampat #spiceislands #ringoffire

0

0

0

3,276

Mast raising without a crane sounds a daunting prospect but it is actually very straightforward if you prepare properly. Some years ago I wrote an article which you can see here, https://www.sailingcatamarans.com/index.php/articles/11-technical-articles/268-safe-mast-lowering-method so this is really just an update. This video shows my Chat 18, which has a mast from a beach cat, and thus one that could be pushed up by hand, but here I show the system that works on any size mast - the biggest I have raised this way was on a 50ft ketch. The key features are a good tabernacle, a "gin pole" - in this case the boom - and most important, the use of temporary shrouds thus ensuring that the mast cannot fall sideways. These shrouds must have "chainplates" that line up exactly with the tabernacle pivot bolt. When down the mast rests on a, eg, dinghy trailer mast support at the back of the cockpit. If you regularly raise you mast you can fit a trailer roller to the bracket, so it's easy to push the mast to and fro for trailering. The "gooseneck" for the ginpole is a shroud adjuster from my junk box, suitably bent and screwed to the front of the mast. Roller reefing gear has to be kept straight and has a tendency to catch on the cabin roof etc. So I always lash it to the ginpole in about the right position. The "chainplates" for the temporary shrouds are, again, from my junk box and are 25mm OD aluminium tubes that clip into place and are easily removed. They also take guywires from the forward end of the ginpole to stop that falling over. I attached the spi halyard to the ginpole, but you can just rely on the forestay/furling gear. The mast is then raised up using the mainsheet shackled to the forestay chainplate (you may need a longer rope, depending on your boat). 4:1 is easy on small boats, on bigger boats lead it back to a winch. Of course the most load is when the mast is horizontal, you often have to push on the mast when lowering to get it to start moving. So if you can get it off the support you know you can hoist it all the way. So it all seems a lot of ropes and preparation but it's all worth it as the mast cannot fall and you always have total control, even in a cross wind. And you can usually raise the mast singlehanded. If you are only occasionally raising/lowering the mast then the temporary stays can be rope. Make a loop in the end and pass it over the spreaders and round the mast using a boathook or, on bigger boats, a bosun's chair. Easy to pull off again afterwards. Before sailing always check the mast with binoculars or camera to ensure there are no twisted shackles or, especially, T bar terminals (which is why I don't recommend T bars on trailable boats.) Use tape or elastic band to hold the stays in the correct position while hoisting - both will break away as the shrouds tighten.

0

0

0

2,234

► Full test in Multihulls World Special Issue Power N°23: https://www.multihulls-world.com/review/motor/makai-m37-automotive-inspired-design ► As soon as it was launched in Croatia, the Makai 37 sailed to Palma, then Venice... and now it’s due in Cannes, perfectly tested on its semi-offshore trip. The Italian design of Emanuele Rossi (ERYD Design) offers this powercat sedan sporty and attractive lines. The catamaran concept is of course exploited so as to offer reduced fuel consumption, impeccable lateral stability and a level of comfort pertaining to a much larger boat. The tunnel between the hulls has been designed to create a shock-absorbing air cushion in rougher seas. The deck plan provides access to the water - or the beach - at the (Kevlar®-reinforced) bow and at the stern. The engine legs can be raised, allowing the boat to take the ground with total safety. This model will be available in a GT version. We’ve already booked in for a test in Split. ► TECHNICAL SPECIFICATIONS : Builder: Makai Yachts Architect: ERYD Design Length: 36’5” (11.1 m) Beam: 15’3” (4.64 m) Draft: 22” (0.55 m) Displacement: 16,750/17,400 lbs (7.6/7.9 t) Engine: 320 or 370 HP Yanmar Sterndrive Fuel: 237 US gal (900 l) Maximum speed: 38 knots Range: up to 700 miles Water: 118 US gal (450 l) CE Category: B12 ► Become a FREE SUBSCRIBER to Multihulls World's YouTube page now - https://www.youtube.com/c/MultihullsWorld ► Log on to our website to discover over 500 multihulls tests! Subscribe to our newsletter to take advantage of our promotions and boat show invitations! https://www.multihulls-world.com/ ► Follow us on Facebook! https://m.facebook.com/MultihullsWorldMag/?locale2=fr_FR ► Discover us on Instagram! https://www.instagram.com/multihulls_world/ ► Follow our multi news on X https://twitter.com/multihullsworld?lang=fr ► Let’s talk about business https://www.linkedin.com/company/multicoques-mag-multihulls-world/ ► Like us on TikTok! https://www.tiktok.com/@multihullsworldmag #multihullsworld #yachting #multihull #cruising #bluewater #sailing #sailcruising #seatrial #boatreview #bluewatersailing #powercat #boat #boatlife #boating #sailingday #magazine #YouTube #tiktok #catamaran #trimaran #makaiyachts #makaim37 #makai37 #emmanuelvandeth #shanegrover @makaiyachts

0

0

0

816

0

0

0

0

887

Pra alegar a semana né

0

0

0

2,687