0

0

0

0

14

0

0

0

0

2,148

⚠️ ATENÇÃO: Para melhor experiência, assista este vídeo em resolução 4K ⚠️ ATENÇÃO: Este vídeo deve ser assistido em sequência pela PLAYLIST: 👉 https://www.youtube.com/playlist?list=PLGt243WbrOa41T7W-G335atM_6k_pXEBj REGATA DE ABERTURA 2026 Uma regata tradicional com a finalidade de abrir a Temporada de Vela da Represa de Guarapiranga, através de uma confraternização festiva, social e beneficente com todos os velejadores da FEVESP, clubes e marinas. A Regata de Abertura é um evento organizado pelo São Paulo Yacht Club e para os velejadores de todos os clubes de vela e marinas membros da FEVESP. ADESSO terminou em 3º Lugar na Regata 08 barcos da classe MARRECO participaram oficialmente desta regata Depois da Regata fomos para Clube SPYC para confraternização e premiação Vídeo Parte 001: Preparação antes da largada. Vídeo Parte 002: Largada. Vídeo Parte 003: Primeira perna da regata. Vídeo Parte 004: Próximo ao CCC. Vídeo Parte 005: Passando CCC. Vídeo Parte 006: Próximo ao Sailing Center Vídeo Parte 007: Montando boias 1 e 2 e subindo vela balão. Vídeo Parte 008: Segunda perna da regata. Vídeo Parte 009: Montando boia 3 e subindo vela balão novamente. Vídeo Parte 010: Montando boia 4 e linha de chegada. Mais sobre o evento em: 👉 https://www.spyc.com.br/regataabertura 👉 https://classemarreco.com.br/classe-marreco 👉 https://www.youtube.com/channel/UCjDvehg2P1NRKBgqxsMrzRw

0

0

0

39

0

0

0

0

684

Screwhead teak plugs in 23 seconds!! Having just replaced around 1000 teak screw head plugs…this was the process.. Unscrew every exposed screw: I used a battery drill driver. Drill the hole deeper: I used a 10mm forstner bit as it fitted the existing holes perfectly and did a tidy job. This is subject to having enough teak left to drill deeper. Fortunately Najad were generous with their teak! Try not to drill as far as the fibreglass. Add sealant and replace the screws: I’ve seen videos where they say the screws were just for construction and you can leave them out. That is probably correct but I’m going for better safe than sorry. If the teak was thinner with no room to drill deeper and replace the screws I’d leave them out as a last chance of getting a few more years out of a worn deck. Sealant to stop any water getting into the deck core. I used a hand screwdriver rather than power to replace them as power was tending to rip out the self tapping screws from the fibreglass. Put glue on the plug: I used a polyurethane foaming wood glue. Epoxy would be very strong but mixing all the batches a big pain if you have lots to do. Try to get more glue on the edges than the base of the plug as I had a couple of plugs pushed out as the glue foamed up. Tap in the plug: I used a standard claw hammer as it’s all I had but I daresay a wooden mallet is recommended but the top of the plug is waste material anyway so it matters not. Cut off the excess: I used a Fein multi tool oscillating saw. Be careful with your angle as you don’t want to gouge the surrounding deck. It took me a few goes to master the technique but was pretty quick when I did. I said the top of the plugs were waste but if you found yourself short a lot of them had enough material left to do more holes. Sand flat: I used a random orbit sander with a worn 80 grit pad. I now have fresh patches all over the deck so, once I’ve completed a couple of caulking touch ups, I’ll give the whole deck a very light sanding. You could just leave the newly sanded plug patches to grey down to match the deck if you preferred. And that’s it…repeat many times! Feel free to ask any questions 😊⛵️ #boatlife #liveaboardsailboat #boatmaintenance #najad #boatrepairs

0

0

0

696