0

0

0

0

138

Avión en la playa

0

0

0

1,150

Embark on an exhilarating underwater odyssey with us as we explore the mesmerizing depths of the Red Sea in Hurghada aboard the luxurious liveaboard vessel, Amelie! Join our diverse group of adventure-seekers from Austria, Germany, Denmark, Croatia, and Wales as we dive into a week-long journey filled with breathtaking encounters with vibrant marine life and stunning coral reefs. Experience the thrill of liveaboard diving as we navigate the crystal-clear waters of the Red Sea, encountering majestic marine creatures and exploring hidden underwater treasures. From vibrant coral gardens to thrilling dive sites, our expedition promises unforgettable moments and lifelong memories. Join us on this unforgettable dive adventure in Hurghada, where every dive is a new discovery and every moment is filled with excitement. Subscribe now to dive deep into the wonders of the Red Sea with us! I hope you'll enjoy this video! If you have any questions, please leave a comment down below. Music: https://www.storyblocks.com/audio Voiceover: https://murf.ai/text-to-speech AI Invideo (10 minutes are free!): https://invideo.io/i/pyu NordVPN - Get 3 months for free!: https://ref.nordvpn.com/ZpghalEIcgd Join me on Instagram: Everything big - https://www.instagram.com/project_yet_unknown_all/ Everything small - https://www.instagram.com/project_yet_unknown/ Check out my pictures on ... Scopio: http://bit.ly/2OtkRLg Wirestock: https://wirestock.io/peter.jantsch

0

0

0

409

0

0

0

0

411

0

0

0

0

785

Screwhead teak plugs in 23 seconds!! Having just replaced around 1000 teak screw head plugs?this was the process.. Unscrew every exposed screw: I used a battery drill driver. Drill the hole deeper: I used a 10mm forstner bit as it fitted the existing holes perfectly and did a tidy job. This is subject to having enough teak left to drill deeper. Fortunately Najad were generous with their teak! Try not to drill as far as the fibreglass. Add sealant and replace the screws: I've seen videos where they say the screws were just for construction and you can leave them out. That is probably correct but I'm going for better safe than sorry. If the teak was thinner with no room to drill deeper and replace the screws I'd leave them out as a last chance of getting a few more years out of a worn deck. Sealant to stop any water getting into the deck core. I used a hand screwdriver rather than power to replace them as power was tending to rip out the self tapping screws from the fibreglass. Put glue on the plug: I used a polyurethane foaming wood glue. Epoxy would be very strong but mixing all the batches a big pain if you have lots to do. Try to get more glue on the edges than the base of the plug as I had a couple of plugs pushed out as the glue foamed up. Tap in the plug: I used a standard claw hammer as it's all I had but I daresay a wooden mallet is recommended but the top of the plug is waste material anyway so it matters not. Cut off the excess: I used a Fein multi tool oscillating saw. Be careful with your angle as you don't want to gouge the surrounding deck. It took me a few goes to master the technique but was pretty quick when I did. I said the top of the plugs were waste but if you found yourself short a lot of them had enough material left to do more holes. Sand flat: I used a random orbit sander with a worn 80 grit pad. I now have fresh patches all over the deck so, once I've completed a couple of caulking touch ups, I'll give the whole deck a very light sanding. You could just leave the newly sanded plug patches to grey down to match the deck if you preferred. And that's it?repeat many times! Feel free to ask any questions ??? #boatlife #liveaboardsailboat #boatmaintenance #najad #boatrepairs

0

0

0

675